We report the development of solution-processed zinc oxide (ZnO) transparent thin-film transistors (TFTs) with a poly(2-hydroxyethyl methacrylate) (PHEMA) gate dielectric on a plastic substrate. The ZnO nanorod film active layer, prepared by microwave heating, showed a highly uniform and densely packed array of large crystal size (58 nm) in the [002] direction of ZnO nanorods on the plasma-treated PHEMA. The flexible ZnO TFTs with the plasma-treated PHEMA gate dielectric exhibited an electron mobility of 1.1 cm(2) V(-1) s(-1), which was higher by a factor of approximately 8.5 than that of ZnO TFTs based on the bare PHEMA gate dielectric.
Electrohydrodynamic (EHD) jet printing has a variety of benefits compared to conventional inkjet techniques, such as high resolution and the ability to work with high-viscosity pastes. In this work, Ag nanoparticles with 4000 cPs were chosen because they are printable on various substrates for electronic devices. The effects of additive on the high-viscosity Ag paste formulation were investigated, and pattern lines narrower than 100 μm were achieved by EHD-jet printing with an average sheet resistance of 0.027 Ω □−1. Furthermore, solution-processed oxide TFTs were fabricated with EHD jet-printed Ag electrodes for the first time. The electrical properties obtained were a current ratio of 1.5 × 106, a mobility of approximately 1 cm2 V−1s−1, a threshold voltage of 21.5 V, and a subthreshold slope of 3.05 V dec−1.
Solution-processed gate dielectrics were fabricated with the combined ZrO2 and Al2O3 (ZAO) in the form of mixed and stacked types for oxide thin film transistors (TFTs). ZAO thin films prepared with double coatings for solid gate dielectrics were characterized by analytical tools. For the first time, the capacitance of the oxide semiconductor was extracted from the capacitance-voltage properties of the zinc-tin oxide (ZTO) TFTs with the combined ZAO dielectrics by using the proposed metal-insulator-semiconductor (MIS) structure model. The capacitance evolution of the semiconductor from the TFT model structure described well the threshold voltage shift observed in the ZTO TFT with the ZAO (1:2) gate dielectric. The electrical properties of the ZTO TFT with a ZAO (1:2) gate dielectric showed low voltage driving with a field effect mobility of 37.01 cm2/Vs, a threshold voltage of 2.00 V, an on-to-off current ratio of 1.46 × 105, and a subthreshold slope of 0.10 V/dec.
The electrohydrodynamic (EHD) jet spraying process is a good method for making quantum dot (QD) layers in light-emitting diodes (LEDs). However, controlling the morphology and large-scale fabrication of the QD layers are critical for realizing all-solution-processed QD-LEDs with high performance. Three spraying techniques were used with the EHD jet spraying technique: a big circular film method, a spiral-line method, and a straight-line method. These techniques were used to obtain QD films with good uniformity. The straight-line spray showed the most promise to obtain a uniform QD layer with large area, and QD-LEDs made with this method showed better performance with a low turn-on voltage of 3.0 V, a luminance of 7801 cd/m2, and a maximum current efficiency of 2.93 cd/A.
A novel electrohydrodynamic (EHD) electrospray coating mechanism was proposed for the continuous fabrication of large-area quantum dot (QD) thin films for high-performance light-emitting diodes (LEDs). The size of QD droplets was systemically controlled using the stable EHD electrospray mode from a mixed solvent, which is a crucial factor for the formation of large and smooth QD thin films. The minimum amount of material consumption was achieved during the process by applying the unique coating system. A QD-LED device based on electrodeposited QDs showed a maximum luminance of 12,082 cd m−2, maximum current efficiency of nearly 4.0 cd A−1, and maximum EQE of 1.86%. This system demonstrates not only high reproducibility but could also pave the way for commercializing high-quality QD-LED devices.