Masoud Sabzi

Dr. Masoud Sabzi


Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 January 2023 in Coatings
Verified
Journal Article
Open access
PDF file
MSMasoud Sabzi
Masoud Sabzi
HMHashem Mousavi-Anijdan
Hashem Mousavi-Anijdan
MSM. Shamsodin
M. Shamsodin
MFM. Farzam
M. Farzam
Akbar Hojjati-NajafabadiAkbar Hojjati-Najafabadi
Akbar Hojjati-Najafabadi
ULUnhae Lee
Unhae Lee
Chemical vapor deposition (CVD) is a process that a solid is formed on a substrate by the chemical reaction in the vapor phase. Employing this technology, a wide range of materials, including ceramic nanocomposite coatings, dielectrics, and single crystalline silicon materials, can be coated on a variety of substrates. Among the factors influencing the design of a CVD system are the dimensions or geometry of the substrate, substrate temperature, chemical composition of the substrate, type of the deposition process, the temperature within the chamber, purity of the target material, and the economics of the production. Three major phenomena of surface reaction (kinetic), diffusion or mass transfer reaction, and desorption reaction are involved during the CVD process. Thermodynamically, CVD technology requires high temperatures and low pressures in most systems. Under such conditions, the Gibbs free energy of the chemical system quickly reaches its lowest value, resulting in the production of solids. The kinetic control of the CVD technology should always be used at low temperatures, and the diffusion control should be done at high temperatures. The coating in the CVD technology is deposited in the temperature range of 900–1400 °C. Overall, it is shown here that by controlling the temperature of the chamber and the purity of the precursors, together with the control of the flow rate of the precursors into the chamber, it is possible to partially control the deposition rate and the microstructure of the ceramic coatings during the CVD process.

6 September 2019 in Materials Research Express
Verified
Journal Article
Closed access
MSMasoud Sabzi
Masoud Sabzi
MFMansour Farzam
Mansour Farzam


1 November 2018 in Ceramics International
Verified
Journal Article
Closed access
MSMasoud Sabzi
Masoud Sabzi
SDS. Mersagh Dezfuli⁠
S. Mersagh Dezfuli⁠
SMS.M. Mirsaeedghazi
S.M. Mirsaeedghazi

6 December 2018 in International Journal of Minerals, Metallurgy and Materials
Verified
Journal Article
Closed access
PDF file
MSMasoud Sabzi
Masoud Sabzi
SFSadegh Moeini Far
Sadegh Moeini Far
SDSaeid Mersagh Dezfuli
Saeid Mersagh Dezfuli

8 January 2018 in Materials Research
Verified
Journal Article
Open access
PDF file
SASeyyed Hashem Mousavi Anijdan
Seyyed Hashem Mousavi Anijdan
MSMasoud Sabzi
Masoud Sabzi
MZMostafa Roghani Zadeh
Mostafa Roghani Zadeh
MFMansour Farzam
Mansour Farzam
Ni-P-(Cu) composite coatings were applied on a St37 steel in an acidic bath of hypophosphite composite. The effect of the concentration of the Cu particles and pH of the solutionon the amount of Ni and P of the coatings, their morphology, and hardness of the coatings were explored. Some of the coated samples were also heat treated at 400ºC for 1 hour. The phases formed, the microstructure and the amount of the alloying elements of the coatings were analyzed by X-Ray powder diffraction (XRD), Scanning Electron Microscope (SEM) equiped with Energy Dispersive Spectroscopy (EDS). Results show that although adding Cu particles reduced the hardness of Ni-P coating (from 482.4 to 351.2 VH in 1 gr/lit Cu), within Ni-P-Cu composite coatings the hardness of Ni-P-Cu composite coating increased from 351.2 to 380.7 VH by increasing the Cu particles from 1 to 7 gr/lit. The structure of the coating was crystalline during the heat treatment making the coating harder. With increasing the pH of the solution from 4.5 to 7 and then to 9, the weight percent of P and the particle of Cu were reduced.