A cooler tin selenide: Thermoelectric materials can convert heat into electricity or be used as the basis of cooling devices. Qin et al . found that doping a tin selenide thermoelectric material with lead and sodium improved the room temperature thermoelectric properties, an effect created by manipulation of the electronic bands. The authors showed that the material could be used not only for power generation but also cooling. If optimal contact materials are identified, then this approach may be attractive for future applications. —BG
9 December 2019 in Journal of Materials Chemistry A
GeTe-based thermoelectric materials tend to be naturally heavily hole doped because of Ge lattice vacancies, and this complicates efforts to improve the figure of merit ZT. Herein, we report that partial substitution of Cd for Ge and doping with Sb can synergistically reduce the density of holes and improve the thermoelectric transport properties of GeTe. Density functional theory electronic structure calculations suggest that when Cd partially substitutes for Ge and forms CdxGe1−xTe, the energy offset between the light and heavy valence bands in both rhombohedral and cubic structures is reduced, promoting multi-band conduction that increases the hole carrier effective mass from 1.44m0 for pristine GeTe to 2.32m0 for Cd0.05Ge0.95Te. The ensuing valence band convergence enhances the Seebeck coefficient and yields a high power factor of 44.5 μW cm−1 K−2 at 800 K. Moreover, DFT calculations show a downward energy profile, indicating that as Cd enters the GeTe lattice it tends to move towards a hypothetical octahedral center to make six equal Cd–Te bonds. Such a local distortion in combination with the large mass and size difference between Ge and Cd strongly intensifies phonon scattering by point defects, lowering the lattice thermal conductivity in CdxGe1−xTe. Subsequent Sb doping in Cd0.03Ge0.97−ySbyTe reduces the inherent high carrier concentration in GeTe, leading to a remarkable enhancement of the Seebeck coefficient and the power factor over a wide temperature range. Furthermore, doping with Sb in Cd0.03Ge0.97−ySbyTe introduces additional point defect phonon scattering that results in an extremely low lattice thermal conductivity ∼ 0.71 W m−1 K−1 at 700 K for the Cd0.03Ge0.89Sb0.08Te sample. All those factors lead to a high thermoelectric figure of merit, ZT ∼ 1.8 at 700 K, and a high average ZT of 1.3 in the temperature interval of 400–800 K attained in Cd0.03Ge0.89Sb0.08Te.
2 November 2019 in Journal of the American Chemical Society
P-type Bi 2− x Sb x Te 3 compounds are crucial for thermoelectric applications at room temperature, with Bi 0.5 Sb 1.5 Te 3 demonstrating superior performance, attributed to its maximum density-of-states effective mass ( m *). However, the underlying electronic origin remains obscure, impeding further performance optimization. Herein, we synthesized high-quality Bi 2− x Sb x Te 3 (00 l ) films and performed comprehensive angle-resolved photoemission spectroscopy (ARPES) measurements and band structure calculations to shed light on the electronic structures. ARPES results directly evidenced that the band convergence along the - direction contributes to the maximum m * of Bi 0.5 Sb 1.5 Te 3 . Moreover, strategic manipulation of intrinsic defects optimized the hole density of Bi 0.5 Sb 1.5 Te 3 , allowing the extra valence band along - to contribute to the electrical transport. The synergy of the above two aspects documented the electronic origins of the Bi 0.5 Sb 1.5 Te 3 ’s superior performance that resulted in an extraordinary power factor of ~5.5 milliwatts per meter per square kelvin. The study offers valuable guidance for further performance optimization of p-type Bi 2− x Sb x Te 3 .