Anja Holst

Mrs. Anja Holst


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 January 2023 in Metals
Verified
Journal Article
Open access
PDF file
AHAnja Holst
Anja Holst
SKStefan Kante
Stefan Kante
ALAndreas Leineweber
Andreas Leineweber
ABAnja Buchwalder
Anja Buchwalder
Unalloyed cast iron materials exhibit low tribological and corrosive resistance. In this respect, nitriding has a wide range of applications for steels. In the case of cast iron, the advantageous properties of nitrided layers are impaired by the presence of graphite. Electron beam remelting of cast iron surfaces prior to nitriding removes graphite. The homogeneous ledeburitic microstructure within the approx. 1 mm-thick remelted layer enables the formation of a dense compound layer during subsequent nitriding. The main objective of this study is to investigate the nitriding mechanism of unalloyed ledeburitic microstructures. Due to the complex relationships, investigations were carried out on both conventional ferritic and pearlitic cast irons and Fe-based model alloys containing one to four additional alloying elements, i.e., C, Si, Mn and Cu. The iron (carbo-)nitride composition (γ’, ε) of this compound layer depends on the gas nitriding conditions, the chemical composition of the substrates and the microstructural constituents. As a result, a schematic model of the nitriding mechanism is developed that includes the effects of the nitriding parameters and alloy composition on the phase composition of the nitriding layer. These findings enable targeted parameter selection and a further optimization of both the process and the properties.

1 September 2019 in Journal of Materials Processing Technology
Verified
Journal Article
Closed access
AHAnja Holst
Anja Holst
ABA. Buchwalder
A. Buchwalder
PHP. Hollmann
P. Hollmann
RZR. Zenker
R. Zenker

24 September 2023 in Materials and Corrosion
Verified
Journal Article
Open access
AHAnja Holst
Anja Holst
HBHorst Biermann
Horst Biermann
ABAnja Buchwalder
Anja Buchwalder
Commercially available gray‐solidified cast iron exhibits reduced load‐carrying capacity under locally concentrated pressure with simultaneous sliding stress. Electron beam remelting dissolves the graphite near the surface, and the surface layer solidifies according to the metastable system. During subsequent gas nitriding, a dense compound layer forms on this white‐solidified, hard surface layer. The phase composition of the compound layer depends not only on the gas nitriding conditions, but also on the chemical composition of the cast iron. The effect of the individual processes of remelting and gas nitriding and their combination on the corrosion behavior of one ferritic and one pearlitic cast iron with different copper contents is investigated using potentiodynamic polarization measurements in 5% sodium chloride solution at room temperature. The remelted and nitrided surface layers exhibit the highest corrosion resistance. The proportion of iron carbonitrides γ' and ε contained in the compound layer influences the corrosion behavior.

1 August 2021 in HTM Journal of Heat Treatment and Materials
Verified
Journal Article
Closed access
AHAnja Holst
Anja Holst
ABA. Buchwalder
A. Buchwalder
RZR. Zenker
R. Zenker
The graphite inclusions typical of grey solidified cast iron materials reduce the load-bearing capacity under locally concentrated pressure and simultaneous sliding stress. Surface treatment processes such as nitriding and electron beam remelting are known to improve the local stress behaviour. In this paper, the effects of the above-mentioned individual processes and their combination on the tribological stress behaviour of ferritic and pearlitic cast irons with different graphite morphologies are discussed. The results obtained in the model wear test ball-plate show that the specific wear coefficient of the investigated cast irons with different graphite morphology can already be reduced by at least one order of magnitude by an approx. 0.5–0.9 mm thick remelted surface layer with a surface hardness of 650–750 HV1. This treatment eliminates the graphite and produces ledeburitic carbides instead. The potential of an additional nitriding treatment depends on the parameters used, i. e. the nitrided layer thickness produced as well as the phase composition and the pore fraction of the compound layer. Based on stress calculations, the experimentally determined main influences such as the coefficient of friction, the pore fraction in the compound layer and the magnitude of the Hertzian pressure on the contact stress could essentially be confirmed.