Papia Sultana

Ms. Papia Sultana


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 September 2024 in Journal of Manufacturing Science and Engineering
Verified
Journal Article
Closed access
PDF file
PSPapia Sultana
Papia Sultana
BQBoqiang Qiang
Boqiang Qiang
CSChangHee Son
ChangHee Son
SKSeho Kim
Seho Kim
GMGlennys Mensing
Glennys Mensing
PFPlacid M. Ferreira
Placid M. Ferreira
Surface-Enhanced Raman Spectroscopy (SERS) is emerging as a powerful tool for detecting and identifying chemical and biological substances because of its high sensitivity, specificity, speed and label-free detection. For SERS substrates to be effective in sensing applications, they must exhibit reproducible and robust high signal enhancement and cost-effective scalability. This paper introduces a highly sensitive, large-area silver SERS substrate patterned with a uniform array of 3-D retroreflecting inverted pyramids and develops manufacturing pathway for it, using a novel and facile electrochemical imprinting process called Solid-State Superionic Stamping (S4). Substrates, approximately 4mm2 in area, are produced and tested with 1,2-bis(4-pyridyl) ethylene (BPE). Uniformly high and reproducible spatially averaged enhancement factor (EF), typically around value of 2 × 107 with relative standard deviation of 6.7% and a high batch-to-batch repeatability with a relative standard deviation of 10.5% between batches were observed. Passivating a substrate's surface with atomically thin layers of alumina, deposited using Atomic Layer Deposition (ALD) was effective in maintaining the EF constant over a 60-day period, albeit with a trade-off between its EF and its lifespan. S4 has the potential to make substrates with EF consistently greater than 107 available at a cost of $1 to $2 per substrate, allowing SERS to be adopted across a wide spectrum of high-volume applications, including security, food safety, medical diagnostics, and chem-bio analysis.

14 February 2023 in Membranes
Verified
Journal Article
Open access
PDF file
PSPapia Sultana
Papia Sultana
MKMujibur Khan
Mujibur Khan
DMDebdyuti Mandal
Debdyuti Mandal
MSMohammadsadegh Saadatzi
Mohammadsadegh Saadatzi
SBSourav Banerjee
Sourav Banerjee
In this work, we report the effect of steady-state atmospheric plasma (Corona discharge) in nanofibers and nanocomposite membranes for piezoelectric applications. The investigation was performed in PVDF (Poly vinylidene fluoride) nanofibers, CNT (Carbon Nanotubes)-reinforced PVDF nanocomposites, and PAN (Poly acrylonitrile) nanofiber membranes. Steady-state plasma was generated with a high voltage power source with 1 mA discharge current output and 6 kV discharge voltage, and the gap between tip and the material was maintained to be 1 cm. For the fabrication of nanofibers and nanocomposite membranes, an electrospinning method was used. The electrospinning parameters, such as flow rate and voltage, were optimally tuned for obtaining uniform nanofibers and nanomembranes. Along with the plasma treatment, heat treatment above the glass transition temperature was also conducted on the nanofiber membranes. Using a Scanning Electron Microscope (SEM), the morphology of the nanofibers was observed. X-ray Diffraction (XRD) demonstrated the polycrystallinity of the nanofibers. Fourier Transform Infrared Spectroscopy (FTIR) analysis of the PVDF nanofibers shows a peak at 796 cm−1 representing α-phase (C-H rocking) in the control sample which is absent in the treated samples. Raman spectroscopy of PVDF nanofibers identifies a Raman shift from 873 cm−1 to 877 cm−1 (denoting β-phase) for plasma-treated samples only. Electron Paramagnetic Resonance (EPR) concludes that the intensity of the free radicals increases from 1.37 to 1.46 (a.u.) after plasma treatment. Then, sensors were fabricated from the PVDF nanofibers, MWCNT-reinforced PVDF nanofibers, and PAN nanofibers to characterize their piezoelectric properties. The impact test results showed that the atmospheric plasma and heat-treated samples had 86%, 277%, and 92% increases of the d33 value (piezoelectric coefficient) in the case of PVDF nanofibers, MWCNT-reinforced nanofibers, and PAN nanofibers, respectively. It was also observed that the capacitance of the nanofiber membranes has increased due to the plasma treatment.