Advancements in energy technologies created a new application for gas turbine generators, which are used to balance load. This usage also brought new challenges for maintenance because of harsh operating conditions that make turbines more susceptible to random failures. At the same time, reliability requirements for energy equipment are high. Reliability-centered maintenance based on forecasting the remaining useful life (RUL) of energy equipment, offers improvements to maintenance scheduling. It requires accurate forecasting methods to be effective. Defining stages in energy equipment operation allows for the improvement of quality of data used for training. At least two stages can be defined: normal operation and degradation process. A new method named Head move—Head move is proposed to robustly identify the degradation process by detecting its starting point. The method is based on two partially overlapping sliding windows moving from the start of operation to the end of life of the energy equipment and Kruskal-Wallis test to compare data within these windows. Using this data separation, a convolutional neural network-based forecasting model is applied for RUL prediction. The results demonstrate that the proposed degradation process identification (DPI) method doubles the accuracy when compared to the same forecasting model but without degradation process identification.
This paper addresses the problem of ensuring the continuous operation of cyber–physical systems (CPS) under conditions of component degradation and wear. To achieve this goal, a transition to the concept of Proactive Prognostics and Health Management (PPHM) is proposed, focused on proactive control of the technical condition of equipment. A key stage of PPHM is the generation of control actions aimed at extending the remaining useful life by adapting the operational parameters of the system. This paper proposes an intelligent support method for generating control actions to optimize the operational conditions. The proposed method integrates an RUL prediction model with optimization procedures based on genetic algorithm. The method was experimentally validated using XJTU-SY Bearing test rig and a bearing-degradation dataset. The obtained results demonstrate its effectiveness and confirm its applicability for extending the service life of technical systems. The proposed method is general and can be adapted to any CPS where controllable parameters affect the degradation rate
Modern industrial equipment is a cyber-physical system (CPS) consisting of physical production components and digital controls. Lowering maintenance costs and increasing availability is important to improve its efficiency. Modern methods, based on solving event prediction problem, in particular, prediction of remaining useful life (RUL) are used as a crucial step in a framework of the reliability-centered maintenance to increase efficiency. But modern methods of RUL forecasting fall short when dealing with real-world scenarios, where CPS are described by multidimensional continuous high frequency data with working cycles with variable duration. To overcome this problem, we propose a new method for faults prediction, which is based on extraction of semantic state vectors (SSV) from working cycles of equipment. To implement SSV extraction, a new method, based on convolutional autoencoder and extraction of hidden state is proposed. In this method, working cycles are detected in input data stream, then they are converted to images, on which autoencoder is trained. The output of an intermediate layer of autoencoder is extracted and processed into SSV. SSVs are then combined into a time series, on which RUL is forecasted. After optimization of hyperparameters the proposed method shows following results: RMSE = 1.799, MAE = 1,374, which is significantly more accurate than existing methods. Therefore, SSV extraction is a viable technique for forecasting RUL.
Modern industrial equipment is a cyber-physical system (CPS) consisting of physical production components and digital controls. Lowering maintenance costs and increasing availability is important to improve its efficiency. Modern methods, based on solving event prediction problem, in particular, prediction of remaining useful life (RUL), are used as a crucial step in a framework of reliability-centered maintenance to increase efficiency. But modern methods of RUL forecasting fall short when dealing with real-world scenarios, where CPS are described by multidimensional continuous high-frequency data with working cycles with variable duration. To overcome this problem, we propose a new method for fault prediction, which is based on extraction of semantic state vectors (SSVs) from working cycles of equipment. To implement SSV extraction, a new method, based on convolutional autoencoder and extraction of hidden state, is proposed. In this method, working cycles are detected in input data stream, and then they are converted to images, on which an autoencoder is trained. The output of an intermediate layer of an autoencoder is extracted and processed into SSVs. SSVs are then combined into a time series on which RUL is forecasted. After optimization of hyperparameters, the proposed method shows the following results: RMSE = 1.799, MAE = 1.374. These values are significantly more accurate than those obtained using existing methods: RMSE = 14.02 and MAE = 10.71. Therefore, SSV extraction is a viable technique for forecasting RUL.