The increase in the number of Unmanned Aerial Vehicles (UAVs) and Micro Air Vehicles (MAVs), which are used in a variety of applications has led to a surge in low Reynolds number aerodynamics research. Flow around fixedwing MAVs has an unusual behavior due to its low aspect ratio and operates at low Reynolds number, which demanded to upgrade the used wind tunnel for this study. This upgrade enables measuring the small aerodynamics forces and moment of fixed-wing MAVs. The wind tunnel used in this work is upgraded with a state of art data acquisition system to deal with the different sensors signals in the wind tunnel. For accurate measurements, the sting balance, angle sensor, and airspeed sensor are calibrated. For validation purposes, an experiment is made on a low aspect ratio flat plate wing at low Reynolds number, and the measured data are corrected and compared with published results. The procedure presented in this paper for the first time gave a detailed and complete guide for upgrading and calibrating old wind tunnel, all the required corrections to correct the measured data was presented, the turbulence level correction new technique presented in this paper could be used to estimate the flow turbulence effect on the measured data and correct the measured data against published data.
The mining industry has recently shown increased interest in drones for routine activities in underground and surface mines. Designing a drone for coal mines is extremely complicated since the Mine Safety and Health Administration (MSHA) has tight guidelines for any equipment that can be used in underground coal mines. Due to these criteria, designing a drone for underground coal mining is exceedingly difficult. This paper explores the challenges of creating an intrinsically safe drone propulsion system. To address the challenges of designing an intrinsically safe drone’s propulsion system for an underground coal mine, this work aims to investigate the potential approaches to enhance efficiency and mitigate the heat. The study begins with the drone’s sizing approach before moving on to the experimental setup that is utilized to test the drone’s propulsion system. Finally, answers to numerous issues arising during the inquiry are offered, and these solutions are empirically explored.
10 March 2021 in Journal of Intelligent & Robotic Systems
The United States has witnessed a concerning surge in the incidence of diseases like Coal Workers’ Pneumoconiosis (CWP), despite numerous efforts aimed at prevention. This study delves into the realm of respiratory health by investigating the deposition of dust particles within the respiratory tract and lungs. By analyzing particles of varying sizes, shapes, velocities, and aerodynamic diameters, we aim to gain a comprehensive understanding of their impact on deposition patterns. This insight could potentially drive changes in dust exposure protocols within mining environments and improve monitoring practices. The interplay of several critical factors, including particle characteristics and an individual’s breathing patterns, plays a pivotal role in determining whether particles settle in the lungs or are exhaled. This paper provides a comprehensive literature review on Respirable Coal Mine Dust (RCMD), with a specific focus on examining particle deposition across different regions of the airway system and lungs. Additionally, we explore the utility of Computational Fluid Dynamics (CFD) in simulating particle behavior within the respiratory system. Predicting the precise behavior of dust particles within the respiratory airway poses a significant challenge. However, through numerical simulations, we aspire to enhance our understanding of strategies to mitigate total lung deposition by comprehensively modeling particle interactions within the respiratory system.
22 November 2022 in Clean Technologies and Environmental Policy
The objective of this paper is to develop a generic electric vehicle battery charging framework using wind energy as the direct energy source. A robust model for a small vertical axis wind turbine based on an artificial neural network algorithm is used for predicting its performance over a wide range of operating conditions. The proposed framework can be implemented at any location worldwide where full prediction of the wind signature is perfectly obtained. In this paper, a small vertical axis wind turbine has been experimentally characterized at different operating conditions, where measured data, output power, and torque have been used to build the model. Once the model has been developed, the model is inserted into the MATLAB/Simulink software tool to predict the charging performance of a battery for an electric vehicle. An rpm controller has been used to achieve the maximum generated power from the wind turbine across the day with various wind speeds. Hence, the generated power is fed to the EV battery charger to implement the constant current constant voltage charging protocol. The charging current reached the desired value in a settling time of 4.5 s, whatever the intermittency of the wind energy. The proposed application of wind energy to EV provides sufficient constant power supported by the utility grid. Graphical Abstract