The new, bio-based, shape-stable, composite phase change materials (PCMs) were designed and characterized for thermal energy storage applications. Coconut oil (CO) as PCM was impregnated into activated carbon (AC)-doped porous polymer composite foam as a support material. Cherry stones (CHSs) were used as AC precursor and AC was obtained by carbonization under N2 atmosphere following the chemical activation with phosphoric acid (PA). The properties of CHSs and AC were determined by elemental analysis, Fourier Transfer Infrared (FTIR) Spectroscopy, Scanning Electron microscope (SEM), and Brunauer–Emmet–Teller (BET) surface area measurements. AC-doped unsaturated polyester resin (UPR)-based composite matrix was prepared by high internal phase emulsion (HIPE) templating approach. The obtained macroporous composite PCM frameworks were fully characterized in terms of chemical, morphological, and mechanical properties and used as support materials for shape stabilization of CO. The composite PCMs were produced successfully and exhibited leak-proof properties. It was found that 5.0 wt% AC-doped composite PCM with a melting enthalpy of 42.92 J · g−1 and a melting temperature of 24.02°C has the highest thermal energy storage capacity. The designed low-cost, bio-based, composite PCMs have application potential for developing smart textile materials with thermo-regulating property. Graphical Abstract
9 November 2021 in Journal of Applied Polymer Science
High Internal Phase Emulsions (HIPEs) of dicyclopentadiene (DCPD) were prepared using mixtures of surface-modified calcite (mCalcite) and a non-ionic surfactant. Twelve different emulsion formulations were created using an experimental design methodology. Three distinctive levels of the internal phase ratio, the amount of mCalcite loading, and the surfactant were used to prepare the HIPEs. Accordingly, macroporous polyDCPD composites were synthesized by performing ring-opening metathesis polymerization (ROMP) on the HIPEs. The variations in the morphological and physical properties of the composites were investigated in terms of experimental parameters. In the end, five different model equations were derived with a confidence level of 95%. The main and binary interaction effects of the experimental parameters on the responses, such as the average cavity size, interconnecting pore size, specific surface area, foam density, and compression modulus, were demonstrated. The synergistic interaction between the amount of surfactant, the amount of mCalcite loading, and the internal phase ratio appeared to have a dominant role in the average cavity diameter. The solo effect of the internal phase ratio on the interconnecting pore size, foam density, and compression modulus was confirmed. In addition, it was demonstrated that the specific surface area of the composites was mainly changed depending on the amount of mCalcite loading.
31 December 2021 in Environmental Research and Technology
Macroporous foams having 80 vol % of nominal porosity were synthesized by the copolymerization crosslinking of glycidyl methacrylate (GMA) based high internal phase emulsions (HIPEs). To alter the mechanical and thermal properties, cellulose nanocrystals (CNCs) were used as filler. For this purpose, CNCs were added to the continuous oil phase during emulsification process at a loading rate of 1, 5 or 7 wt %. Consequently, composite foams were obtained by purification of the polymerized HIPEs (polyHIPEs). The effect of CNCs on the morphological and mechanical properties was investigated. It was found that CNCs have a significant influence on the thermal stability and the compressive strength of the obtained foams. In the end, the neat polyHIPE foam and the polyHIPE/CNC composite foam with 1 wt % of CNC were post-functionalized by reacting phenylimidazole (PIAL) with the epoxy ring of the GMA units. Resulting amine functional foams and the neat foam were utilized in Cr(III) removal from aqueous solutions. It was demonstrated that amine functional foams have a great potential as sorbent materials. The results also showed that the existence of CNCs decreased the performance for removing Cr(III) ions. Nevertheless, functionalization by PIAL significantly improved the selectivity of Cr(III) in comperasion with the neat polyHIPE foam.