Musibau Olalekan Ogunlana

Dr. Musibau Olalekan Ogunlana


Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 December 2022 in Materials
Verified
Journal Article
Open access
PDF file
MOMusibau Olalekan Ogunlana
Musibau Olalekan Ogunlana
MMMammo Muchie
Mammo Muchie
OOOluseyi Philip Oladijo
Oluseyi Philip Oladijo
MEMutiu Erinosho
Mutiu Erinosho
Titanium carbide (TiC) thin films were deposited by radio frequency magnetron sputtering (RFMS) onto a copper substrate by using Argon (Ar) gas plasma at a gas flow rate of 10.0 sccm. The effect of time and temperature at a constant RF power on the structural and tribological properties were respectively investigated by atomic force spectroscopy (AFM), X–ray Diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, optical microscopy (OM), scanning electron microscopy (SEM) and tribological measurements. All films were tested to have crystal structures with the preferential plane (111) and dominant plane (200) grain orientations. Thus, plane (111) has phase identification of Cu(Cu16Ti)0.23 for some samples, whereas plane (200) has a phase identification of Cu(Cu0.997Ti0.003) and Cu(Cu0.923Ti0.077) for other samples. The lowest thin film roughness of 19.797 nm was observed in the sample, with RF power, sputtering time, and a temperature of 200 W, for two hours and 80 °C, respectively. The FTIR spectra of TiC films formed under different sputtering times (2–3 h) and temperatures (80 °C–100 °C) on Cu substrates at a constant sputtering power of 200 W in the range of 5000–500 cm−1. The peaks at 540 cm−1, 780 cm−1, and 1250 cm−1 are presented in the FTIR spectra and the formation of a Ti–C bond was observed. On the other hand, a sample was revealed to have the lowest wear volume of 5.1 × 10−3 mm3 while another sample was obtained with the highest wear volume of 9.3 × 10−3 mm3.

29 February 2024 in Coatings
Verified
Journal Article
Open access
PDF file
MOMusibau Olalekan Ogunlana
Musibau Olalekan Ogunlana
MMMammo Muchie
Mammo Muchie
RSRiaan Adriaan Swanepoel
Riaan Adriaan Swanepoel
OAOlukorede Tijani Adenuga
Olukorede Tijani Adenuga
OOOluseyi Philip Oladijo
Oluseyi Philip Oladijo
Titanium carbide materials are introduced into manufacturing industries for the reinforcement and surface protection of base materials due to their substantial ability to withstand severe environments, which include sliding wear, corrosion, and mechanical failures. A thin film of titanium carbide (TiC) is coated onto brass and copper substrates using the radio frequency magnetron sputtering (RFMS) deposition method. The coating process is carried out at constant processing parameters, which include a sputtering power of 200 W, a temperature of 80 °C, a deposition time of 180 min, and an argon (Ar) gas flow rate at 10 standard cubic centimetres per minute (SCCM). The coating, together with the base materials, is modelled and its behaviours are simulated using ANSYS Workbench R19.2 Academic, supported by Mechanical APDL solver for nonlinear finite element analysis (FEA). The deformation, equivalent stress–strain characteristics, and elastic–plastic properties of the coating are determined at applied loads of 60 N and 25 N and coefficients of friction (CoF) of 0.25 and 0.38 for the thin film deposition on brass and copper substrates. The sliding distance and the speed of the alloy steel ball used during the sliding wear operation are found to be 3 mm and 4 mm/s, respectively. The sliding wear modelling and simulation process are, however, designed for the ball-on-flat (BoF) wear technique with a dry sliding approach. Therefore, BoF wear simulations are also performed on titanium carbide–brass (TiC-Br) and titanium carbide–copper (TiC-Cu) conjugates for the evaluation of surface engineering applications such as cutting tools and in automotive, aerospace, thermomechanical, and biomedical fields. The ball used for the FEA wear simulation is made from alloy steel material (AISI 52100) with a radius of 3.175 mm.