The solar water heater can be integrated into future residential buildings as the main energy source, which will subsequently reduce the energy cost of water heating. An original configuration for an efficient Domestic Hot Water (DHW) storage tank is developed and experimentally evaluated under Saharan climate. This novel DHW configuration includes a hybrid (solar and electric) energy system with a flat plate solar collector coupled with an electric heater. Additionally, a phase change material (PCM) mixture that is composed of paraffin wax and animal fat with a melting temperature between 35.58 °C and 62.58 °C and latent heat between 180 and 210 kJ/kg is integrated into this novel tank configuration. The experimental results indicated that hot water production by using latent heat storage could be economically attractive. By evaluating the cost of water heating expressed in Algerian dinar per liter (DZD/L), it was found that one liter of hot water may cost around 0.1362 DZD/L (i.e., 0.00096 USD/L) compared to 0.4431 DZD/L for the conventional water heater, an average energy cost savings of 69.26%. On a yearly basis, the average energy cost savings may reach up to 80.25% if optimal tilt for the solar collector is adopted on a monthly basis. The flat plate collector may be vulnerable to convective heat transfer; therefore, other solar collectors, such as vacuum tube collectors, may provide enhanced energy performance.
The solar water heater must be integrated into future residential buildings as the main energy source, which will subsequently reduce the energy cost of water heating. An original configuration for efficient Domestic Hot Water "DHW" storage tank is developed and experimentally evaluated under Saharan climate. This novel DHW configuration includes a hybrid (solar and electric) energy system with a flat plate solar collector coupled with an electric heater. Additionally, phase change material "PCM" mixture that is composed of paraffin wax and animal fat with a melting temperature between 35.58°C and 62.58°C and latent heat between 180 and 210 kJ/kg is integrated into this novel tank configuration. The experimental results indicated that hot water production by using latent heat storage could be economically attractive. In this proposed configuration, one liter of hot water may cost around 0.1362 DZD/liter (i.e., 0.00096 US$/liter) compared to 0.4431 DZD/liter for the conventional water heater, an average energy cost savings of 69.26%. On a yearly basis, the average energy cost savings may reach up to 80.25% if optimal tilt for the solar collector is adopted on a monthly basis. The flat plate collector may be vulnerable to convective heat transfer, and therefore, other solar collectors such as vacuum tube collectors may provide enhanced energy performance.
This study offers a comparative analysis of two most important types of thermoresponsive hydrogels: poly(N-isopropylacrylamide) (PNiPAM) and poly(alkylene glycol) methacrylates (PAGMA). The latter includes poly(oligo(ethylene glycol) methacrylate) (POEGMA), a moderately hydrophilic polymer, and poly(oligo(propylene glycol) methacrylate) (POPGMA), its more hydrophobic counterpart. The hydrogels were produced using gamma irradiation in three different solvent systems: demineralized water, a water/ethanol mixture, and pure ethanol. Gel fraction measurements were used to assess the effects of monomer type, irradiation dose, and solvent composition on crosslinking efficiency. Swelling behavior was examined over a wide temperature range, highlighting distinct thermoresponsive features and volume phase transition temperatures. Differential scanning calorimetry confirmed the presence of temperature-dependent phase transitions, while structural and chemical changes caused by radiation-induced crosslinking were analyzed using Fourier-transform infrared spectroscopy. Results showed that effective hydrogel formation is achievable at relatively low radiation doses. The choice of synthesis medium significantly influenced the formation and the gelation efficiency of hydrogels. Particularly, PNiPAM hydrogels were successfully synthesized without the use of alcohol and still demonstrated excellent swelling capacity and volume phase transition temperatures near physiological temperatures, making them suitable for biomedical applications. These findings provide valuable insights for designing advanced smart hydrogels for biomedical and environmental uses.