Xiqiang Zhao

Dr. Xiqiang Zhao


Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 May 2016 in Drying Technology
Verified
Journal Article
Closed access
ZSZhanlong Song
Zhanlong Song
LYLiansheng Yao
Liansheng Yao
CJChuanming Jing
Chuanming Jing
XZXiqiang Zhao
Xiqiang Zhao
WWWenlong Wang
Wenlong Wang
CMChunyuan Ma
Chunyuan Ma
Because of lignite’s high moisture content, it must be dried before most applications. Microwave radiation may be suitable for efficient drying because of its special heating properties. This study investigated the drying behavior of lignite samples from eastern Inner Mongolia by microwave thermogravimetric analysis. Three stages of microwave drying were observed: preheating, fast weight loss, and falling rate drying periods. Samples’ surface temperatures increased dramatically during preheating, dropped slightly in the second period, and rose again in the final period. The measured surface temperature was <95°C during microwave heating. The overall moisture content decreased more rapidly under higher microwave power. Fine lignite particles (diameter <0.2 mm) and lump samples (particle size 10 mm) dried better than granular lignite (particle size 1–2 mm). The samples also underwent slight natural drying (1–2% point reduction in moisture content) after microwave treatment. The critical moisture content of lignite (11–15% under experimental conditions) was redefined. Energy consumption was analyzed to evaluate the feasibility of the proposed drying process.

11 May 2023 in Processes
Verified
Journal Article
Open access
PDF file
Jing SunJing Sun
Jing Sun
WCWenxin Chen
Wenxin Chen
JXJia Xin
Jia Xin
SLSu Li
Su Li
PJPingshan Jia
Pingshan Jia
SCShouyan Chen
Shouyan Chen
The robust development of electric vehicles has driven a surging decommission stream of lithium-ion batteries (LIBs) owing to their limited service life. The recycling of spent LIBs has become an urgent and essential task for the sustainable development of the LIB industry. However, the prevailing recycling methods focus only on recycling valuable metal, whilst the graphite anode materials are usually discarded or burned as fuels, leading to great waste of valuable carbon material. A facile strategy to obtain value-added products in an efficient manner is of great significance for the recycling of spent graphite. As graphite has excellent microwave absorption capability and electrical conductivity, microwave radiation on spent graphite can induce a Joule heat–discharge–plasma coupled effect, leading to a rapid heating process, especially when discharge occurs, exhibiting a thermal shock effect with the generation of a large number of high-energy electrons and active materials. This special feature facilitates microwave heating that is tailored for assisting the removal of impurities, structure repair, and graphite intercalation and exfoliation in an efficient manner. Therefore, different from the conventional graphite recycling route that is associated with energy/solution-intensive processes, this paper reviews the progress on microwave-assisted removal of impurities, repair of damaged graphite structure, and innovatively discusses the breakthroughs in microwave-assisted preparation of graphite intercalation compounds, expanded graphite, graphene and graphene-based materials, and porous graphene, with an aim to provide a scientific reference for the value-added resource utilization of spent graphite and preparation of new energy storage materials.

20 August 2016 in Waste Management & Research: The Journal for a Sustainable Circular Economy
Verified
Journal Article
Closed access
ZSZhanlong Song
Zhanlong Song
YYYaqing Yang
Yaqing Yang
LZLong Zhou
Long Zhou
XZXiqiang Zhao
Xiqiang Zhao
WWWenlong Wang
Wenlong Wang
CMChunyuan Ma
Chunyuan Ma
The pyrolytic characteristics of tyre powder treated under different microwave powers (300, 500, and 700 W) were studied via microwave thermogravimetric analysis. The product yields at different power levels were studied, along with comparative analysis of microwave pyrolysis and conventional pyrolysis. The feedstock underwent preheating, intense pyrolysis, and final pyrolysis in sequence. The main and secondary weight loss peaks observed during the intense pyrolysis stage were attributed to the decomposition of natural rubbers and synthetic rubbers, respectively. The total mass loss rates, bulk temperatures, and maximum temperatures were distinctively higher at higher powers. However, the maximum mass loss rate (0.005 s-1), the highest yields of liquid product (53%), and the minimum yields of residual solid samples (43.83%) were obtained at 500 W. Compared with conventional pyrolysis, microwave pyrolysis exhibited significantly different behaviour with faster reaction rates, which can decrease the decomposition temperatures of both natural and synthetic rubber by approximately 110 °C–140 °C.

4 January 2023 in Energies
Verified
Journal Article
Open access
PDF file
HWHongfei Wang
Hongfei Wang
ZYZhipeng Yu
Zhipeng Yu
JZJie Zhou
Jie Zhou
CLChengming Li
Chengming Li
AJAnanthanarasimhan Jayanarasimhan
Ananthanarasimhan Jayanarasimhan
Hao ZhangHao Zhang
Hao Zhang
Electrocatalytic CO2 reduction is regarded as a green and promising technology because it can convert carbon dioxide into value-added fuel or chemicals in a flexible and sustainable way. This research aimed to comprehensively analyze the research hotspots and trends in the field of CO2 electroreduction from 2005 to 2022 using bibliometric methods based on the core database of Web of Science. The results showed that 4546 papers on CO2 electroreduction were retrieved from 2005 to 2022, with a clear increasing trend. The research direction was diversified, involving multiple disciplines, and it is a comprehensive research field. ACS Catalysis is the journal with the largest number of articles. China is the country with the largest number of documents and has made significant contributions to the development and progress of this field. Copper-based catalysts are still the research focus in recent years. It is of great practical significance to develop copper-based catalysts with high efficiency, low cost, high stability, and high selectivity for the preparation of C1 products.

15 September 2024 in Journal of Colloid and Interface Science
Verified
Journal Article
Closed access
HWHongfei Wang
Hongfei Wang
FZFusen Zhang
Fusen Zhang
YLYang Li
Yang Li
YPYingping Pang
Yingping Pang
XZXiqiang Zhao
Xiqiang Zhao
YMYanpeng Mao
Yanpeng Mao

13 June 2024 in Nanomaterials
Verified
Journal Article
Open access
PDF file
SXShijing Xie
Shijing Xie
MLMin Lei
Min Lei
JSJiawei Sun
Jiawei Sun
CYChongdou Yang
Chongdou Yang
WLWenbo Liu
Wenbo Liu
Jie QiuJie Qiu
Jie Qiu
The corrosion behavior of 20G and TP347H materials was investigated in molten LiCl-NaCl-KCl salt. The corrosion rates of these materials in molten chloride salt are high and are strongly affected by the alloying surface oxide formation. The 20G shows uniform surface corrosion with almost no protective oxide formation on the surface. In contrast, the austenitic steel TP347H exhibits better corrosion resistance in molten chloride salts due to its high Cr content. Owing to the highly corrosive nature of molten chloride salts, the Cl− in molten salt could react with oxides and alloy, inducing intergranular corrosion of austenitic steel in molten chloride salt environments.