Recent advancements in space technology and reduced launching cost led companies, defence and government organisations to turn their attention to low Earth orbit (LEO) and very low Earth orbit (VLEO) satellites, for they offer significant advantages over other types of spacecraft and present an attractive solution for observation, communication and other tasks. However, keeping satellites in LEO and VLEO presents a unique set of challenges, in addition to those typically associated with exposure to space environment such as damage from space debris, thermal fluctuations, radiation and thermal management in vacuum. The structural and functional elements of LEO and especially VLEO satellites are significantly affected by residual atmosphere and, in particular, atomic oxygen (AO). At VLEO, the remaining atmosphere is dense enough to create significant drag and quicky de-orbit satellites; thus, thrusters are needed to keep them on a stable orbit. Atomic oxygen-induced material erosion is another key challenge to overcome during the design phase of LEO and VLEO spacecraft. This review covered the corrosion interactions between the satellites and the low orbit environment, and how it can be minimised through the use of carbon-based nanomaterials and their composites. The review also discussed key mechanisms and challenges underpinning material design and fabrication, and it outlined the current research in this area.

The emergence of antibiotic resistant microorganisms possesses a great threat to human health and the environment. Considering the exponential increase in the spread of antibiotic resistant microorganisms, it would be prudent to consider the use of alternative antimicrobial agents or therapies. Only a sustainable, sustained, determined, and coordinated international effort will provide the solutions needed for the future. Plant secondary metabolites show bactericidal and bacteriostatic activity similar to that of conventional antibiotics. However, to effectively eliminate infection, secondary metabolites may need to be activated by heat treatment or combined with other therapies. Cold atmospheric plasma therapy is yet another novel approach that has proven antimicrobial effects. In this review, we explore the physiochemical mechanisms that may give rise to the improved antimicrobial activity of secondary metabolites when combined with cold atmospheric plasma therapy.

Development of sustainable agriculture on Mars is a critical step towards its colonisation. However, Martian regolith is coarse-grained, and its mineral profile differs significantly from that of terrestrial arable soil, resulting in poor seed germination success and stunted plant development. This study investigates whether germination success and plant growth can be improved by exposing seeds and plants to water enriched with either i) biochemically active reactive oxygen and nitrogen species generated by atmospheric pressure plasma (PAW) or (ii) nano-/micro-bubbles and minerals such as potassium and calcium extracted from Aquapulse^® feldspar (APW), a type of rock that is readily available on Mars, at different stages of the crop lifecycle. As a crop model, microgreen crops of B. oleracea and M. sativa are chosen for their short growth cycle, low resource requirements, and high nutritional value. For B. oleracea crops, soaking of seeds in PAW followed by irrigation with APW led to an increase in germination by ~566.7%, in biomass by 412.4%, and in chlorophyll content by 17.7% compared to crops grown using normal water for seed soaking and irrigation. For M. sativa crops, the use of APW for soaking and irrigation yielded an increase of 41.7% in seed germination and 45.2% in crop biomass, whereas the use of PAW for both soaking and irrigation resulted in the greatest improvement in seed germination, 41.7%, when compared to control. These results suggest that, with further optimisation, a regiment of treatment with PAW and APW in place of normal water can be used to address stage-specific challenges of the crop lifecycle in Martian regolith. As amending Martian regolith with a minimum of 1% organic matter is required to promote healthy plant development, further studies should investigate the use of plasma-mediated reforming of biowaste for in situ production of e.g., biochar.

The conversion efficiency of a thermoelectric power generator depends on the dimensionless figure-of-merit (ZT) of the constituent thermoelectric materials, which is mainly determined by their Seebeck coefficient as well as the electrical and thermal conductivity. ZnO holds promise for thermoelectric applications, yet its use is currently limited by low electrical conductivity and high thermal conductivity. Herein, we demonstrate how thermal conductivity of ZnO can be significantly reduced by intelligently combining it with a cellulose-based Ag fabric using a one-step hydrothermal method, and how different ratios of zinc nitrate hexahydrate (ZNH) to hexamethylenetetramine (HMT) can be used to fine-tune the thermoelectric performance of the resulting composite. We show that as-prepared samples have a composite structure of Ag, Zn and O without any other impurity phases. We propose that the facet dependent crystal growth orientation, from the c-axis in (101) planes to the a-axis in (100) plane, amplify phonon scattering within the material, impeding effective heat transfer and thereby lowering overall thermal conductivity to 0.046 W/mK at room temperature for composites with a 1:1 ZNH to HMT ratio.

Plasma polymer coatings fabricated from Melaleuca alternifolia essential oil and its derivatives have been previously shown to reduce the extent of microbial adhesion on titanium, polymers, and other implantable materials used in dentistry. Previous studies have shown these coatings to maintain their performance under standard operating conditions; however, when used in e.g., a dental implant, these coatings may inadvertently become subject to in situ cleaning treatments, such as those using an atmospheric pressure plasma jet, a promising tool for the effective in situ removal of biofilms from tissues and implant surfaces. Here, we investigated the effect of such an exposure on the antimicrobial performance of the Melaleuca alternifolia polymer coating. It was found that direct exposure of the polymer coating surface to the jet for periods less than 60 s was sufficient to induce changes in its surface chemistry and topography, affecting its ability to retard subsequent microbial attachment. The exact effect of the jet exposure depended on the chemistry of the polymer coating, the length of plasma treatment, cell type, and incubation conditions. The change in the antimicrobial activity for polymer coatings fabricated at powers of 20–30 W was not statistically significant due to their limited baseline bioactivity. Interestingly, the bioactivity of polymer coatings fabricated at 10 and 15 W against Staphylococcus aureus cells was temporarily improved after the treatment, which could be attributed to the generation of loosely attached bioactive fragments on the treated surface, resulting in an increase in the dose of the bioactive agents being eluted by the surface. Attachment and proliferation of Pseudomonas aeruginosa cells and mixed cultures were less affected by changes in the bioactivity profile of the surface. The sensitivity of the cells to the change imparted by the jet treatment was also found to be dependent on their origin culture, with mature biofilm-derived P. aeruginosa bacterial cells showing a greater ability to colonize the surface when compared to its planktonic broth-grown counterpart. The presence of plasma-generated reactive oxygen and nitrogen species in the culture media was also found to enhance the bioactivity of polymer coatings fabricated at power levels of 10 and 15 W, due to a synergistic effect arising from simultaneous exposure of cells to reactive oxygen and nitrogen species (RONS) and eluted bioactive fragments. These results suggest that it is important to consider the possible implications of inadvertent changes in the properties and performance of plasma polymer coatings as a result of exposure to in situ decontamination, to both prevent suboptimal performance and to exploit possible synergies that may arise for some polymer coating-surface treatment combinations.