Textile industries release dangerous wastewater that contain dyes into the environment. Due to their toxic, carcinogenic and mutagenic nature, they must be removed before the discharge. Liquid–liquid extraction has proven to be an efficient method for the removal of these dyes. As extractants, deep eutectic solvents (DESs) have shown excellent results in recent years, as well as presenting several green properties. Therefore, four different hydrophobic DESs based on natural components were prepared thymol:decanoic acid (T:D (1:1)), thymol:DL-menthol (T:M (1:1)), thymol:DL-menthol (T:M (1:2)) and thymol:coumarin (T:C (2:1)) for the extraction of Malachite Green (MG), Brilliant Blue G (BBG), Acid Yellow 73 (AY73), Reactive Red 29 (RR29), Acid Blue 113 (AB113), Reactive Black 5 (RB5), Remazol Brilliant Blue (RBB), Direct Yellow 27 (DY27), Acid Blue 80 (AB80), Direct Blue 15 (DB15) and Acid Violet 43 (AV43) dyes from water. The operational parameters of the liquid–liquid extraction were selected in order to save time and materials, resulting in 30 min of stirring, 15 min of centrifugation and an aqueous:organic ratio of 5:1. In these conditions, the highest values of extraction obtained were 99% for MG, 89% for BBG and 94% for AY73. Based on these results, the influence of the aqueous:organic phase ratio and the number of necessary stages to achieve water decolorization was studied.
A novel approach to enhance the utilization of low-cost and sustainable chitosan for wastewater remediation is presented in this investigation. The study centers around the modification of chitosan beads using a deep eutectic solvent composed of choline chloride and urea at a molar ratio of 1:2, followed by treatment with sulfuric acid using an impregnation accessible methodology. The effectiveness of the modified chitosan beads as an adsorbent was evaluated by studying the removal of the azo dye Reactive Black 5 (RB5) from aqueous solutions. Remarkably, the modified chitosan beads demonstrated a substantial increase in adsorption efficiency, achieving excellent removal of RB5 within the concentration range of 25–250 mg/L, ultimately leading to complete elimination. Several key parameters influencing the adsorption process were investigated, including initial RB5 concentration, adsorbent dosage, contact time, temperature, and pH. Quantitative analysis revealed that the pseudo-second-order kinetic model provided the best fit for the experimental data at lower dye concentrations, while the intraparticle diffusion model showed superior performance at higher RB5 concentration ranges (150–250 mg/L). The experimental data were successfully explained by the Langmuir isotherm model, and the maximum adsorption capacities were found to be 116.78 mg/g at 298 K and 379.90 mg/g at 318 K. Desorption studies demonstrated that approximately 41.7% of the dye could be successfully desorbed in a single cycle. Moreover, the regenerated adsorbent exhibited highly efficient RB5 removal (80.0–87.6%) for at least five consecutive uses. The outstanding adsorption properties of the modified chitosan beads can be attributed to the increased porosity, surface area, and swelling behavior resulting from the acidic treatment in combination with the DES modification. These findings establish the modified chitosan beads as a stable, versatile, and reusable eco-friendly adsorbent with high potential for industrial implementation.
The removal of the azo dyes Orange II (OII) and Reactive Black 5 (RB5) from aqueous solutions was studied using three types of adsorbents derived from chitosan: unmodified chitosan beads (un-Ch), chitosan beads tuned with a deep eutectic solvent (DES) composed of choline chloride:urea at a 1:2 molar ratio (Ch-DES), along with FeO nanoparticles added to chitosan and modified with DES (Ch-FeO-DES). Both dyes were effectively removed in 3–4 h when Ch-DES beads were used, at a dye concentration range of 25–50 mg/L. The modification with DES improved the removal efficiency to achieve increases of around 32% for OII and 17% for RB5. The adsorbent dosage and the initial dye concentration influenced the adsorption process. Isotherm adsorption models (Langmuir, Freundlich, and Temkin) and kinetic models (pseudo-first-order, pseudo-second-order, intraparticle diffusion, and Elovich models) were applied to identify the adsorption behavior. The process could be characterized by employing the pseudo-second-order kinetic model and fitting it to the monolayer Langmuir isotherm. The adsorption occurred on a monolayer with no interaction among dye molecules when electrostatic forces would determine the attaching of dye molecules on the adsorbent. OII was efficiently desorbed by an alkaline solution, while RB5 was more strongly attached. The adsorbent could be recycled, after regeneration with an acid solution, for at least 5 reuse cycles while still achieving effective OII removal. Reactivation with a diluted EDTA solution allowed the authors to recycle RB5-attached beads, achieving optimum removal in two further uses.