SUMMARY: Robotic devices are well-suited to provide high intensity upper limb therapy in order to induce plasticity and facilitate recovery from brain and spinal cord injury. In order to realise gains in functional independence, devices that target the distal joints of the arm are necessary. Further, the robotic device must exhibit key dynamic properties that enable both high dynamic transparency for assessment, and implementation of novel interaction control modes that significantly engage the participant. In this paper, we present the kinematic design, dynamical characterization, and clinical validation of the RiceWrist-S, a serial robotic mechanism that facilitates rehabilitation of the forearm in pronation-supination, and of the wrist in flexion-extension and radial-ulnar deviation. The RiceWrist-Grip, a grip force sensing handle, is shown to provide grip force measurements that correlate well with those acquired from a hand dynamometer. Clinical validation via a single case study of incomplete spinal cord injury rehabilitation for an individual with injury at the C3-5 level showed moderate gains in clinical outcome measures. Robotic measures of movement smoothness also captured gains, supporting our hypothesis that intensive upper limb rehabilitation with the RiceWrist-S would show beneficial outcomes.
21 April 2016 in IEEE/ASME Transactions on Mechatronics
Robots are increasingly designed to physically interact with humans in unstructured environments, and as such must operate both accurately and safely. Leveraging compliant actuation, typically in the form of series elastic actuators (SEAs), can guarantee this required level of safety. To date, a number of frequency-domain techniques have been proposed, which yield effective SEA torque and impedance control; however, these methods are accompanied by undesirable stability constraints. In this paper, we instead focus on a time-domain approach to the control of SEAs, and adapt two existing control techniques for SEA platforms. First, a model reference adaptive controller is developed, which requires no prior knowledge of system parameters and can specify desired closed-loop torque characteristics. Second, the time-domain passivity approach is modified to control desired impedances in a manner that temporarily allows the SEA to passively render impedances greater than the actuator's intrinsic stiffness. This approach also provides conditions for passivity when augmenting any stable SEA torque controller with an arbitrary impedance. The resultant techniques are experimentally validated on a custom prototype SEA.compliant actuation,frequency-domain techniquesundesirable stability constraints.
1 December 2016 in IEEE Transactions on Neural Systems and Rehabilitation Engineering
We demonstrate the interaction control capabilities of the MR-SoftWrist, a novel MR-compatible robot capable of applying accurate kinesthetic feedback to wrist pointing movements executed during fMRI. The MR-SoftWrist, based on a novel design that combines parallel piezoelectric actuation with compliant force feedback, is capable of delivering 1.5 N·m of torque to the wrist of an interacting subject about the flexion/extension and radial/ulnar deviation axes. The robot workspace, defined by admissible wrist rotation angles, fully includes a circle with a 20 deg radius. Via dynamic characterization, we demonstrate capability for transparent operation with low (10% of maximum torque output) back drivability torques at nominal speeds. Moreover, we demonstrate a 5.5 Hz stiffness control bandwidth for a 14 dB range of virtual stiffness values, corresponding to 25%-125% of the device's physical reflected stiffness in the nominal configuration. We finally validate the possibility of operation during fMRI via a case study involving one healthy subject. Our validation experiment demonstrates the capability of the device to apply kinesthetic feedback to elicit distinguishable kinetic and neural responses without significant degradation of image quality or task-induced head movements. With this study, we demonstrate the feasibility of MR-compatible devices like the MR-SoftWrist to be used in support of motor control experiments investigating wrist pointing under robotapplied force fields. Such future studies may elucidate fundamental neural mechanisms enabling robot-assisted motor skill learning, which is crucial for robot-aided neuro rehabilitation.
20 February 2015 in IEEE/ASME Transactions on Mechatronics
This paper describes the mechatronic design and characterization of a novel MR-compatible actuation system designed for a parallel force-feedback exoskeleton for measurement and/or assistance of wrist pointing movements during functional neuroimaging. The developed actuator is based on the interposition of custom compliant elements in series between a nonbackdrivable MR-compatible ultrasonic piezoelectric motor and the actuator output. The inclusion of physical compliance allows estimation of interaction force, enabling force-feedback control and stable rendering of a wide range of haptic environments during continuous scanning. Through accurate inner-loop velocity compensation and force-feedback control, the actuator is capable of displaying both a low-impedance subject-in-charge mode and a high stiffness mode. These modes enable the execution of shared haptic protocols during continuous functional magnetic resonance imaging. The detailed experimental characterization of the actuation system is presented, including a backdrivability analysis, demonstrating an achievable impedance range of 22 dB, within a bandwidth of 4 Hz (for low stiffness). The stiffness control bandwidth depends on the specific value of stiffness: a bandwidth of 4 Hz is achieved at low stiffness (10% of the physical springs stiffness), while 8 Hz is demonstrated at higher stiffness. Moreover, coupled stability is demonstrated also for stiffness values substantially (25%) higher than the physical stiffness of the spring. Finally, compatibility tests conducted in a 3T scanner are presented, validating the potential of inclusion of the actuator in an exoskeleton system for support of wrist movements during continuous MR scanning, without significant reduction in image quality.
In this paper, a novel haptic feedback scheme, used for accurately positioning a 1DOF virtual wrist prosthesis through sensory substitution, is presented. The scheme employs a three-node tactor array and discretely and selectively modulates the stimulation frequency of each tactor to relay 11 discrete haptic stimuli to the user. Able-bodied participants were able to move the virtual wrist prosthesis via a surface electromyography based controller. The participants evaluated the feedback scheme without visual or audio feedback and relied solely on the haptic feedback alone to correctly position the hand. The scheme was evaluated through both normal (perpendicular) and shear (lateral) stimulations applied on the forearm. Normal stimulations were applied through a prototype device previously developed by the authors while shear stimulations were generated using an ubiquitous coin motor vibrotactor. Trials with no feedback served as a baseline to compare results within the study and to the literature. The results indicated that using normal and shear stimulations resulted in accurately positioning the virtual wrist, but were not significantly different. Using haptic feedback was substantially better than no feedback. The results found in this study are significant since the feedback scheme allows for using relatively few tactors to relay rich haptic information to the user and can be learned easily despite a relatively short amount of training. Additionally, the results are important for the haptic community since they contradict the common conception in the literature that normal stimulation is inferior to shear. From an ergonomic perspective normal stimulation has the potential to benefit upper limb amputees since it can operate at lower frequencies than shear-based vibrotactors while also generating less noise. Through further tuning of the novel haptic feedback scheme and normal stimulation device, a compact and comfortable sensory substitution device for upper limb amputees might be created.
This paper presents the MR-SoftWrist: a parallel 3DOF MR-compatible wrist robot with compliant actuation. Through a design that aligns the wrist joint axes to the device DOFs and uses custom MR-compatible force-feedback actuation, the MR-SoftWrist can measure and support wrist movements during fMRI. The device has a circular workspace for wrist flexion/extension and radial/ulnar deviation with 18 deg radius, and is capable of generating 1.75 Nm joint torque. Control experiments validate the device's workspace, along with position and zero torque control capabilities. In zero torque mode the maximum force felt by the user is 0.15 Nm, less than 10% of the device's torque output. The device is shown to have no significant affect on imaging quality during fMRI.