LTE-based satellite systems in LEO constellations are a promising solution for extending broadband coverage to areas not connected to a terrestrial infrastructure. However, the large delays and Doppler shifts over the satellite channel pose severe technical challenges to a traditional LTE system. In this paper, two architectures are proposed for a LEO mega-constellation realizing a satellite-enabled LTE system, in which the on-ground LTE entity is either an eNB (Sat-eNB) or a Relay Node (Sat-RN). Focusing on the latter, the impact of large delays and Doppler shifts on LTE PHY/MAC procedures is discussed and assessed. It will be shown that, while carrier spacings, Random Access, and RN attach procedures do not pose specific issues, HARQ requires substantial modifications. Moreover, advanced handover procedures will be also required due to the satellites' movement.

Summary: The integration of satellite and terrestrial networks is a promising solution for extending broadband coverage to areas not connected to a terrestrial infrastructure, as also demonstrated by recent commercial and standardisation endeavours. However, the large delays and Doppler shifts over the satellite channel pose severe technical challenges to traditional terrestrial systems, as long‐term evolution (LTE) or 5G. In this paper, 2 architectures are proposed for a low Earth orbit mega‐constellation realising a satellite‐enabled LTE system, in which the on‐ground LTE entity is either an eNB (Sat‐eNB) or a relay node (Sat‐RN). The impact of satellite channel impairments as large delays and Doppler shifts on LTE PHY/MAC procedures is discussed and assessed. The proposed analysis shows that, while carrier spacings, random access and RN attach procedures do not pose specific issues and hybrid automatic repeat request requires substantial modifications. Moreover, advanced handover procedures will be also required due to the satellites' movement.

Embedded sensors (ESs) are used in smart materials to enable continuous and permanent measurements of their structural integrity, while sensing technology involves developing sensors, sensory systems, or smart materials that monitor a wide range of properties of materials. Incorporating 3D-printed sensors into hosting structures has grown in popularity because of improved assembly processes, reduced system complexity, and lower fabrication costs. 3D-printed sensors can be embedded into structures and attached to surfaces through two methods: attaching to surfaces or embedding in 3D-printed sensors. We discussed various additive manufacturing techniques for fabricating sensors in this review. We also discussed the many strategies for manufacturing sensors using additive manufacturing, as well as how sensors are integrated into the manufacturing process. The review also explained the fundamental mechanisms used in sensors and their applications. The study demonstrated that embedded 3D printing sensors facilitate the development of additive sensor materials for smart goods and the Internet of Things.

Next generation satellite payload technology is expected to provide digital processing capabilities. This will pave the way to regard satellites as flying base stations. However, the initial access procedure must be improved. In this work we focus on non-geostationary earth orbit (NGEO) satellite networks. In this scenario, the random access preamble signal and the detection must be robust to large carrier frequency offsets (CFOs). Towards this end, we investigate the adoption of the pruned discrete Fourier transform spread filter bank multicarrier waveform. The proposed design is suitable for the access scheme of forthcoming 5G-based NGEO satellite communications. The reason is twofold. First, it improves the spectral confinement with respect to the standard single-carrier frequency-division multiplexing (SC-FDM) waveform. Second, it achieves a high level of commonality with 5G new radio, by keeping unchanged the subcarrier spacing, the slot duration and the preamble sequence. Remarkably, the new design allows the straightforward application of non-coherent post detection integration (NCPDI) techniques, which divide the correlation in blocks. Numerical results show that the proposed solution reduces out-of-band emissions and the missed detection probability in presence of CFO, with respect to the conventional approach based on SCFDM and preamble detection with full-length correlation.

The verticals of 5G, such as the automotive, smart grid, and smart cities sectors, will bring new sensors and IoT devices requiring Internet connectivity. Most of these machine-type terminals will be sparsely distributed, covering a very large geographical area and, from time to time, will have to update their software, firmware, and/or other relevant data. Given this situation, one viable solution to implement the “Over-the-Air” update of these IoT terminals can be done with the aid of GEO satellite systems. However, due to the ultra-dense radio frequency reuse factor that contemporary High-Throughput Satellite (HTS) systems implement in the access link to serve the IoT terminals, the use of a time-packed Free Space Optical (FSO) link represents a practical solution to avoid the bottleneck that the satellite gateway experiences in the feeder link. The performance of both Detect-and-Forward and Decode-and-Forward relaying strategies are studied, assuming that the single-carrier M-PAM symbols that are transmitted on the optical feeder link are mapped into M-QAM symbols that modulate the multiple sub-carriers of the OFDM-based radio access link. In addition, the benefits of encapsulating the NB-IoT frames into DVB-S2(X) satellite frames is also analyzed in detail. The effects of the impairments introduced in both the optical feeder and radio access links are characterized in detail, and the end-to-end error correction capabilities of the Modulation and Coding Schemes (MCS) defined in the contemporary releases of the NB-IoT and DVB-S2(X) standards are studied for different working regimes.