Masoud Bodaghi

Dr. Masoud Bodaghi


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 March 2023 in Frontiers in Materials
Verified
Journal Article
Open access
MBMasoud Bodaghi
Masoud Bodaghi
DDDoriane Delfrari
Doriane Delfrari
MLMargot Lucas
Margot Lucas
NSNoha-Lys Senoussaoui
Noha-Lys Senoussaoui
YKYao Koutsawa
Yao Koutsawa
HPHenri Perrin
Henri Perrin
This paper focuses on the morphology evolution in the forming process of unidirectional flax reinforced polypropylene composite laminates. The link between the morphology evolution and thermal conductivity during consolidation stages is investigated. Hot press forming allows to manufacture several composite laminates at different consolidation stages as a function of the compaction thickness. Microscopic evolution of the laminates in terms of morphology and porosity fractions are evaluated by scanning electron microscopy and X-ray microtomography (µ-CT). Hot disk technique is applied to measure the thermal conductivity of the laminates in in-plane and transverse directions. It is found that the in-plane thermal conductivity almost linearly increases with the reduction of porosity fraction. However, the transverse thermal conductivity remained constant. Beside the proposed relations, a theoretical model, based on a two-level Mori-Tanaka homogenization method is proposed. Considering the three-phases material (i.e., porosity, fiber, and polymer matrix), there is a good agreement between the experiment data and model predictions, but limited predictivity for porosity level above 15% certainly due to simplifying assumptions used in the predictive model.

28 February 2023 in Polymers
Verified
Journal Article
Open access
PDF file
HPHenri Perrin
Henri Perrin
MBMasoud Bodaghi
Masoud Bodaghi
VBVincent Berthé
Vincent Berthé
RVREGIS VAUDEMONT
REGIS VAUDEMONT
The melt strength of Elium® acrylic resin is an important factor to ensure limited fluid flow during welding. To provide Elium® with a suitable melt strength via a slight crosslink, this study examines the effect of two dimethacrylates, namely butanediol-di-methacrylate (BDDMA) and tricyclo-decane-dimethanol-di-methacrylate (TCDDMDA), on the weldability of acrylic-based glass fibre composites. The resin system impregnating a five-layer woven glass preform is a mixture of Elium® acrylic resin, an initiator, and each of the multifunctional methacrylate monomers in the range of 0 to 2 parts per hundred resin (phr). Composite plates are manufactured by vacuum infusion (VI) at an ambient temperature and welded by using the infrared (IR) welding technique. The mechanical thermal analysis of the composites containing multifunctional methacrylate monomers higher than 0.25 phr shows a very little strain for the temperature range of 50 °C to 220 °C. The quantity of 0.25 phr of both of the multifunctional methacrylate monomers in the Elium® matrix improves the maximum bound shear strength of the weld by 50% compared to those compositions without the multifunctional methacrylate monomers.

10 January 2023 in Materials
Verified
Journal Article
Open access
PDF file
HPHenri Perrin
Henri Perrin
MBMasoud Bodaghi
Masoud Bodaghi
VBVincent Berthé
Vincent Berthé
SKSébastien Klein
Sébastien Klein
RVREGIS VAUDEMONT
REGIS VAUDEMONT
Joining of dissimilar thermoplastics and their composites is a challenge for thermal welding techniques due to different melting points. Reactive welding with an auxiliary functional material can offer the clear opportunities to develop joining processes due to robustness to joining dissimilar thermoplastic polymers and their composites. The current study employed reactive compatibilization to offer the possibility of joining an acrylic-based glass fiber composite to polyamide (PA)-12 by applying a hot-tool welding technique. For this purpose, composite plates are fabricated by a typical vacuum infusion and thin layer thermoplastic films are formed by a thermostamping of PA12 granules. Subsequently, the reactive welding of the interposed PA12 sheet and Elium®-GMA-Glass composite is conducted by hot-plate welding. A glycidyl methacrylate (GMA) as a compatibilizing agent is copolymerized with methyl methacrylate Elium® resin. During the hot-tool welding process of dissimilar thermoplastic material, GMA can react with the polyamide end groups. The heat distribution at the Elium® GMA/PA-12 interface is responsible for obtaining a strong joint. This study focuses on the functionality of the compatibilizer on the welding of acrylic-based composites with polyamide (PA)-12 while varying the assembly temperature. The flatwise tensile test proved the effectiveness of GMA on the interface bounding. The excellent bounding incompatible polymers Elium® resin (PMMA) and PA12 was achieved at 200 °C.

25 November 2023 in Materials
Verified
Journal Article
Open access
PDF file
HPHenri Perrin
Henri Perrin
RVREGIS VAUDEMONT
REGIS VAUDEMONT
MBMasoud Bodaghi
Masoud Bodaghi
In this study, a high-Tg aerospace-grade epoxy composite plate was co-curing welded using a unidirectional PEEK thermoplastic carbon fibre tape to develop advanced composite joints. To account for the surface roughness and the weldability of carbon–epoxy/carbon–PEEK composites, plasma treatments were performed. The co-curing was conducted by the following steps: each treated thermoplastic tape was first placed in the mould, and followed by nine layers of dry-woven carbon fabrics. The mould was sealed using a vacuum bag, and a bi-component thermoset (RTM6) impregnated the preform. To understand the role of curing kinetics, post-curing, curing temperature, and dwell time on the quality of joints, five cure cycles were programmed. The strengths of the welded joints were investigated via the interlayer peeling test. Furthermore, cross-sections of welded zones were assessed using scanning electron microscopy in terms of the morphology of the PEEK/epoxy interphase after co-curing. The preliminary results showed that the cure cycle is an important controlling parameter for crack propagation. A noticeable distinction was evident between the samples cured first at 140 °C for 2 h and then at 180 °C for 2 h, and those cured initially at 150 °C for 2 h followed by 180 °C for 2 h. In other words, the samples subjected to the latter curing conditions exhibited consistently reproducible results with minimal errors compared to different samples. The reduced errors confirmed the reproducibility of these samples, indicating that the adhesion between CF/PEEK and CF/RTM6 tends to be more stable in this curing scenario.

3 October 2025 in Applied Sciences
Verified
Journal Article
Open access
PDF file
JMJoão Machado
João Machado
MBMasoud Bodaghi
Masoud Bodaghi
SASuresh Advani
Suresh Advani
NCNuno Curado-Correia
Nuno Curado-Correia
In Liquid Composite Molding (LCM), the high variability present in reinforcement properties such as permeability creates additional challenges during the injection process, such as void formation. Although improved injection strategy designs can mitigate the formation of defects, these processes can benefit from real-time process monitoring and control to adapt the injection conditions when needed. In this study, a machine vision algorithm is proposed, with the objective of detecting and tracking both fluid flow and bubbles in an LCM setup. In this preliminary design, 3D-printed porous geometries are used to mimic the architecture of textile reinforcements. The results confirm the applicability of the proposed approach, as the detection and tracking of the objects of interest is possible, without the need to incur in elaborate experimental preparations, such as coloring the fluid to increase contrast, or complex lighting conditions. Additionally, the proposed approach allowed for the formulation of a new dimensionless number to characterize bubble transport efficiency, offering a quantitative metric for evaluating void transport dynamics. This research underscores the potential of data-driven approaches in addressing manufacturing challenges in LCM by reducing the overall process monitoring complexity, as well as using the acquired reliable data to develop robust, data-driven models that offer new understanding of process dynamics and contribute to improving manufacturing efficiency.