Wonho Lee

Dr. Wonho Lee

Department of Polymer Science and Engineering, Kumoh National Institute of Technology, Gumi‐si 39177, Gyeongbuk, Republic of Korea
orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 May 2024 in Advanced Materials
Verified
Journal Article
Open access
JPJinseok Park
Jinseok Park
HSHyeonseok Seong
Hyeonseok Seong
CYChanho Yuk
Chanho Yuk
DLDongkyu Lee
Dongkyu Lee
YBYouyoung Byun
Youyoung Byun
BKBumjoon J. Kim
Bumjoon J. Kim
This work demonstrates the low‐temperature operation of solid‐state lithium metal batteries (LMBs) through the development of a fluorinated and plastic‐crystal‐embedded elastomeric electrolyte (F‐PCEE). The F‐PCEE is formed via polymerization‐induced phase separation between the polymer matrix and plastic crystal phase, offering a high mechanical strain (≈300%) and ionic conductivity (≈0.23 mS cm−1) at −10 °C. Notably, strong phase separation between two phases leads to the selective distribution of lithium (Li) salts within the plastic crystal phase, enabling superior elasticity and high ionic conductivity at low temperatures. The F‐PCEE in a Li/LiNi0.8Co0.1Mn0.1O2 full cell maintains 74.4% and 42.5% of discharge capacity at −10 °C and −20 °C, respectively, compared to that at 25 °C. Furthermore, the full cell exhibits 85.3% capacity retention after 150 cycles at −10 °C and a high cut‐off voltage of 4.5 V, representing one of the highest cycling performances among the reported solid polymer electrolytes for low‐temperature LMBs. This work attributes the prolonged cycling lifetime of F‐PCEE at −10 °C to the great mechanical robustness to suppress the Li‐dendrite growth and ability to form superior LiF‐rich interphases. This study establishes the design strategies of elastomeric electrolytes for developing solid‐state LMBs operating at low temperatures and high voltages.

6 July 2022 in Advanced Science
Verified
Journal Article
Open access
MJMin Hun Jee
Min Hun Jee
HRHwa Sook Ryu
Hwa Sook Ryu
DLDongmin Lee
Dongmin Lee
WLWonho Lee
Wonho Lee
HWHan Young Woo
Han Young Woo
Recently, sequential layer‐by‐layer (LbL) organic solar cells (OSCs) have attracted significant attention owing to their favorable p–i–n vertical phase separation, efficient charge transport/extraction, and potential for lab‐to‐fab large‐scale production, achieving high power conversion efficiencies (PCEs) of over 18%. This review first summarizes recent studies on various approaches to obtain ideal vertical D/A phase separation in nonfullerene acceptor (NFAs)‐based LbL OSCs by proper solvent selection, processing additives, protecting solvent treatment, ternary blends, etc. Additionally, the longer exciton diffusion length of NFAs compared with fullerene derivatives, which provides a new scope for further improvement in the performance of LbL OSCs, is been discussed. Large‐area device/module production by LbL techniques and device stability issues, including thermal and mechanical stability, are also reviewed. Finally, the current challenges and prospects for further progress toward their eventual commercialization are discussed.

26 September 2017 in Journal of Materials Chemistry A
Verified
Journal Article
Closed access
PDF file
TKTaesu Kim
Taesu Kim
RYRobert Younts
Robert Younts
WLWonho Lee
Wonho Lee
SLSeungjin Lee
Seungjin Lee
KGKenan Gundogdu
Kenan Gundogdu
BKBumjoon J. Kim
Bumjoon J. Kim
The photodegeneration of polymer solar cells (PSCs) based on polymer donors and fullerene acceptors limits their lifetime and reliability. Here, we demonstrate that replacing fullerene acceptors with naphthalenediimide (NDI)-based n-type polymers can significantly enhance the photo-stability of PSCs. As a model system, we compared the photo-stabilities of all-polymer solar cells (all-PSCs) and fullerene-based PSCs (fullerene-PSCs) using the same polymer donor (PBDTTTPD) exposed to one sunlight illumination. We observed a remarkable contrast in their photo-stabilities. After 4 days of irradiation, the performance of the fullerene-PSCs dropped by 50%, whereas the performance of the all-PSCs remained stable. The detailed analysis of charge dynamics measured by femtosecond transient absorption spectroscopy and space charge limited current measurements shows significant reduction in interfacial charge transfer and charge carrier mobility, which correlates with the loss in JSC and FF of the fullerene-PSCs under solar illumination. By contrast, for the all-PSCs, the ultrafast dynamics and charge mobility remained consistent after illumination. The NDI-based copolymer had high stability under light exposure, whereas the photo-induced dimerization of phenyl-C61-butyric acid methyl ester (PCBM) acceptors was responsible for the photo-degradation of fullerene-PSCs.

12 February 2018 in Journal of Materials Chemistry A
Verified
Journal Article
Closed access
PDF file
WLWonho Lee
Wonho Lee
JKJae-Han Kim
Jae-Han Kim
TKTaesu Kim
Taesu Kim
SKSeonha Kim
Seonha Kim
CLChangyeon Lee
Changyeon Lee
BKBumjoon J. Kim
Bumjoon J. Kim
In this study, we demonstrate that the introduction of small amounts of phenyl-C71-butyric acid methyl ester (PC71BM) into all-polymer solar cells (all-PSCs) increases the photovoltaic performance without compromising mechanical properties. Ternary blend polymer solar cells (ternary-PSCs) consisting of a polymer donor (PTB7-Th) and an acceptor mixture with different weight ratios of a polymeric acceptor (P(NDI2HD-T2)) and PC71BM demonstrate the effects of PC71BM loading on the power conversion efficiency (PCE) and mechanical properties. A significant enhancement in the PCEs of ternary-PSCs, from 6.32% to 7.33%, is observed when PC71BM is added into the active layer as up to 30 wt% of the acceptor mixture. Importantly, the excellent mechanical properties (i.e., crack onset strain = 11.6%, toughness = 2237 J m−3) of the blend films are well preserved at PC71BM loadings at or below 30 wt%. In contrast, both the PCE and the mechanical performance of the ternary-PSCs significantly decrease at higher PC71BM loadings (>50 wt%). Detailed morphological analysis via grazing incidence X-ray scattering measurements reveals that PC71BM molecules are well-dispersed in the amorphous portion of the active layer at PC71BM loadings up to 30 wt%. Therefore, both the mechanical and photovoltaic performances of the ternary-PSCs correlate closely with their morphological behavior, particularly in terms of the mixing behavior of PC71BM with polymers. The well-dispersed PC71BM molecules in the amorphous polymer domains facilitate efficient exciton dissociation, whereas the formation of PC71BM aggregates above a critical concentration causes severe mechanical degradation of the ternary-PSCs due to the presence of weak interfaces between the brittle PC71BM and polymer domains. Therefore, the ternary blends with optimal content of polymer/fullerene acceptors represent important candidates for flexible and wearable solar cells that require both high mechanical and photovoltaic performances.

26 February 2024 in Advanced Science
Verified
Journal Article
Open access
JSJunho Sung
Junho Sung
SCSein Chung
Sein Chung
YJYongchan Jang
Yongchan Jang
HJHyoik Jang
Hyoik Jang
JKJiyeon Kim
Jiyeon Kim
ELEunho Lee
Eunho Lee
Interest has grown in services that consume a significant amount of energy, such as large language models (LLMs), and research is being conducted worldwide on synaptic devices for neuromorphic hardware. However, various complex processes are problematic for the implementation of synaptic properties. Here, synaptic characteristics are implemented through a novel method, namely side chain control of conjugated polymers. The developed devices exhibit the characteristics of the biological brain, especially spike‐timing‐dependent plasticity (STDP), high‐pass filtering, and long‐term potentiation/depression (LTP/D). Moreover, the fabricated synaptic devices show enhanced nonvolatile characteristics, such as long retention time (≈102 s), high ratio of Gmax/Gmin, high linearity, and reliable cyclic endurance (≈103 pulses). This study presents a new pathway for next‐generation neuromorphic computing by modulating conjugated polymers with side chain control, thereby achieving high‐performance synaptic properties.

19 September 2024 in Small Structures
Verified
Journal Article
Open access
JSJunho Sung
Junho Sung
MKMinji Kim
Minji Kim
Sein ChungSein Chung
Sein Chung
YJYongchan Jang
Yongchan Jang
SKSoyoung Kim
Soyoung Kim
ELEunho Lee
Eunho Lee
Electrolyte‐gated organic synaptic transistors (EGOSTs) have shed light on their potential in bioelectronics and neuromorphic computing. Numerous research have been studied to modulate their electrochemical doping performance and formulate a simple approach to control iontronics through the side‐chain modulations; however, the effects of alkyl groups as side moieties have not been studied in detail on EGOSTs. Herein, the structural and electrical properties of conjugated polymers are systematically controlled through copolymerization with two different‐alkyl group‐derived monomers for enhancing the nonvolatile characteristics of EGOSTs. The relationships between crystal orientation and electrochemical doping states of conjugated copolymers, which varied with the different copolymerization ratios, are revealed. Also, the behavior of biological synapses, including paired‐pulse facilitation, spike timing‐dependent plasticity, and long‐term potentiation/depression, are successfully simulated. In this study, new avenues are opened for the implementation of neuromorphic devices through side‐chain engineering by showing that the alkyl chain modulates the doping performance.