WOONSUK JUNG

Mr. WOONSUK JUNG


Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 December 2022 in Electronics
Verified
Journal Article
Open access
PDF file
CNChangyun Na
Changyun Na
BJByung-Min Jeon
Byung-Min Jeon
KKKim Kim
Kim Kim
WJWOONSUK JUNG
WOONSUK JUNG
JJJae Seong Jeong
Jae Seong Jeong
HPHwasun Park
Hwasun Park
In this paper, we prepared a pure Sn microbump with a diameter of 30 µm using an electroplating method for a solder cap on a Cu post/Ni barrier and then determined its IMC characteristics and shear strength according to reflow recovery. In order to secure uniformity of the bump height, it was optimized through WID and WIW evaluation methods. Using an optimized plating system, bumps with a diameter of 30 µm, a height of 40 µm, and a space of 50 µm were formed on a 4-inch wafer. Shear strength was measured according to the number of reflows. IMC was evaluated through cross-sectional and plane analyses of bumps. Its correlation with shear strength according to the number of reflows was derived. The Sn plating system optimized each process condition according to the Sn concentration, current density, and temperature. The shape, surface condition, and height uniformity of the bump were quantified by a 3D profiler and FIB analysis. Height uniformity (WID) according to the concentration was confirmed to be approximately 2% when the Sn concentration was 60 g/L. WID according to the additive was confirmed to be 2% when the Sn concentration was 60 mL/L. WID according to the plating temperature was excellent in the shape of the bump at 30 °C, and a value of 2% was confirmed. The WIW for the Sn plating thickness on a 4-inch wafer was confirmed to have a value of ±3.88%. A shear test between the Cu and Sn junction was conducted to verify the shear strength of the manufactured bump. At this time, reflow was performed 1, 3, 5, 7, and 10 times for each sample. It was confirmed that as the number of flows increased, shear strength first increased. It then decreased sharply. It was confirmed that as the number of reflows increased, the thickness and cross-section area of the IMC first increased. They then gradually became saturated. The IMC between Cu and Sn was created in island form at the beginning of the reflow, resulting in increased roughness and shear strength. However, as the number of reflows increased, the roughness decreased since the IMC generated by the island was combined. The shear strength also decreased sharply.

3 October 2025 in Materials
Verified
Journal Article
Open access
PDF file
HPHwasun Park
Hwasun Park
CNChang-Yun Na
Chang-Yun Na
KKKim Kim
Kim Kim
WJWOONSUK JUNG
WOONSUK JUNG
JPJAE-HYUK PARK
JAE-HYUK PARK
YYYoungoo Yang
Youngoo Yang
We evaluated for the morphology and growth behavior of IMC grain according to number of reflows of solder cap pure Sn microbumps. In the structure of Ni barrier/Cu layer between Cu pillar and pure Sn, solder cap pure Sn on the top layer was analyzed for the behavior change of IMC grain according to the number of reflows. The height and diameter of the bumps on the wafer were designed to be 40 μm and 30 μm, respectively. The vertical structure of the microbump consisted of Ti/Cu (1000 Å/2000 Å), Cu pillar (20 µm), Ni barrier (3 µm), and Cu (1 µm). The overall height of the bump is about 40 μm. Additionally, the height of the solder cap pure Sn as the last layer is 20 μm. The diameter of the bump is 30 μm. It was formed using plating. After plating to solder cap Sn, it was finally formed for the microbump using reflow. Samples were prepared according to the number of reflows (1, 3, 5, 7, and 9). To observe the grain morphology of the IMC, the pure Sn on the upper layer (solder cap) was removed using SupraBond RO-22 etchant. In the removed state, the morphology of the IMC grain was evaluated to the inside surface of bump using SEM and a 3D scope. The average number of IMC grains decreased linearly during reflow cycles 1 to 5 and then gradually decreased during reflow cycles 7 to 10. The average surface area of IMC grains was 18.243 μm when reflow was performed once. The average surface area of IMC grains increased proportionally for reflow cycles 1 to 10. Based on the experimental results, when the count of reflow was performed more than 10 times, it was confirmed that the solder cap pure Sn was reduced by more than 50% due to the increase in the area of IMC grain.