Solid oxides have been extensively investigated as possible high-temperature CO 2 sorbents by a number of research groups. We summarised the different strategies to develop synthetic solid oxide sorbents.
Using a combination of characterisation techniques including 3D electron diffraction (3D ED) and powder X-ray diffraction, we reveal that the long-believed hexagonal Na 2 ZrO 3 , is, in fact, Na 2 ZrO 3 with three different types of structural disorder.
23 February 2023 in Journal of Materials Chemistry A
Solid-state synthesis of Na 2 HfO 3 can produce a high-temperature CO 2 sorbent that reaches close to 100% of the theoretical maximum CO 2 uptake (up to ∼15 wt%) with a minimal decrease in CO 2 uptake even after 100 cycles.
For the first time, the use of stannate-based sorbents was investigated as high temperature CO2 sorption to evaluate their potential to contribute towards reducing carbon emissions. The sorption capacity and kinetics of commercial tin oxide, sodium, potassium and calcium stannates and lab synthesised potassium stannates were tested using thermogravimetric analysis. Commercial K2SnO3 was found to possess the largest CO2 uptake capacity (2.77 mmol CO2/g or 12.2 wt%) at 700 °C, which is among the highest for potassium sorbents, but the CO2 desorption was not successful. On the contrary, the in-house synthesised K-stannate (K-B) using facile solid-state synthesis outperformed the other sorbents, resulting in a CO2 uptake of 7.3 wt% after 5 min, an adsorption rate (0.016 mg/s) one order of magnitude higher than the other stannates, and stability after 40 cycles. The XRD and XPS analyses showed that K-B contains a mixture of K2SnO3 (76%) and K4SnO4 (21%), while the Scherrer crystal sizes confirmed good resistance to sintering for the potassium stannates. Among the apparent kinetic model tested, the pseudo-second order model was the most suitable to predict the CO2 sorption process of K-B, indicating that chemical adsorption is dominant, while film-diffusion resistance and intra-particle diffusion resistance governed the sorption process in K-B. In summary, this work shows that solid-state synthesised potassium stannate could be an effective sorbent for high temperature separation, and additional work is required to further elucidate its potential.
Efficient, facile, and energy-efficient desorption processes are highly sought after in industrial processes. Visible light exists all around us and can be considered a ubiquitous energy source that can be used to drive photothermal processes such as the release of guest molecules from porous sorbents. Herein, we present four sustainably synthesized porous coordination polymers, M(dhbq)(H2O)2 (where dhbq = 2,5-dihydroxy-1,4-benzoquinone, and M = Fe, Mg, Mn, or Zn) with visible light photoresponsive properties. Efficient desorption of CO2 corresponding to up to 47.6 % of the total uptake capacity was achieved upon visible light irradiation for 10 min. A negligible decrease (<97 %) in CO2 uptake was observed for up to 10 light-swing adsorption cycles and working capacities of up to 37.5 g kg- were obtained in Fe(dhbq). M(dhbq) possess highly desirable properties that make them interesting for applications related to cost-effective and energy-efficient desorption processes.
Hybrid ultramicroprous materials (HUMs) with a number of different variations of the inorganic pillars as well as surface functional groups have been tested as CO2 sorbent for low-concentration CO2 capture. Specifically well-known HUM NbOFFIVE-1-Ni (NbOFFIVE=(NbOF5)2-, 1=pyz, Ni=nickel(II)) like HUMs were synthesized in this study by replaces Nb with V and Ta. Replacing the metal center from Nb to V or Ta showed that the CO2 adsorption isotherm, in particular at low partial pressures, adopted different shapes and gradient. This study shows that the CO2 adsorption properties at low partial pressures on HUMs can be affected by the metal present in the inorganic pillars.