Dynamic loading of embankment, foundation and pavement structures results in particle breakage of the constituent granular materials, when the stresses imposed on their particles exceed their strength. This paper presents the results of a number of drained cyclic triaxial tests on loose, uniformly graded samples of Dogs bay carbonate sand. It is observed that particle breakage is dependent on stress level, cyclic stress ratio, and creep and is directly related to volumetric strain. Drained cycling increases volumetric strain and therefore more breakage occurs when larger numbers of cycles are imposed. The increase in particle breakage from one cycle to the next indicates that while particles may not be loaded to their full capacity in a given cycle, they can be crushed in subsequent cycles without any variation in the amplitude of cyclic loading.
Recently, considerable efforts have been made in the attempt to map quick clay areas using electrical resistivity measurements. However there is a lack of understanding regarding which soil parameters control the measured resistivity values. To address this issue, inverted resistivity values from 15 marine clay sites in Norway have been compared with basic geotechnical index properties. It was found that the resistivity value is strongly controlled by the salt content of the pore fluid. Resistivity decreases rapidly with increasing salt content. There is also a relatively clear trend of decreasing resistivity with increasing clay content and plasticity index. Resistivity values become very low (≈5 Ω·m) for high clay content (>50%), medium- to high-plasticity (Ip ≈ 20%) materials with salt content values greater than about 8 g/L (or corresponding remoulded shear strength values greater than 4 kPa). For the range of values studied, there is poor correlation between resistivity and bulk density and between resistivity and water content. The data studied suggest that the range of resistivity values corresponding to quick clay is 10 to 100 Ω·m, which is consistent with other published limits. A comparison is made between two-dimensional electrical resistivity tomography (ERT) and resistivity cone penetration test (RCPTU) data for two of the sites and the two sets of data show similar trends and values irrespective of scale effect.
A database of research-quality piezocone cone penetration test (CPTU) and shear wave velocity, Vs, information for Norwegian marine clays has been assembled to study the small-strain stiffness relationships for these materials and to examine the potential use of CPTU and Vs data in combination for the purposes of characterizing these soils. Data for sites where high-quality block sampling was carried out have mostly been used. Improvements have been suggested to existing correlations between the small-strain shear modulus, Gmax, or Vs and index properties for these soils. Recent research has shown that CPTU corrected cone tip resistance, qt, and especially the pore pressure measured during CPTUs, u2, and Vs can be measured reliably and repeatably and are not operator or equipment dependant. Therefore, a new soil classification chart involving the normalized cone resistance, Qt, and normalized shear wave velocity, Vs1, or Vs1 and Δu/[ ] (where u is the pore-water pressure and [ ] is the in situ vertical effective stress) is presented. Using this chart it is possible to clearly distinguish between clays of different overconsolidation ratios (OCRs).
The characterisation of soils for civil engineering purposes depends on removing sufficiently high-quality samples from the ground. Accurate evaluation of sample quality is therefore important if reliable design parameters are to be determined. This paper describes the use of unconfined shear wave velocity (Vs) and suction (ur) measurements to assess sample quality rapidly in soft clay. Samples of varying quality from three well-characterised soft clay sites are initially assessed using conventional techniques, and their results compared with Vsand urmeasurements performed on the same samples. It is observed that the quality of samples indicated by these measurements is very similar to those inferred from traditional disturbance measures, with Vsbeing the more reliable indicator. A tentative empirically derived criterion, based on samples tested in this project, is proposed to quantify sample disturbance combining both Vsand urmeasurements. Further work using this criterion on different materials is important so as to test its usefulness.
The UK’s transportation network is supported by critical geotechnical assets (cuttings/embankments/dams) that require sustainable, cost-effective management, while maintaining an appropriate service level to meet social, economic, and environmental needs. Recent effects of extreme weather on these geotechnical assets have highlighted their vulnerability to climate variations. We have assessed the potential of surface wave data to portray the climate-related variations in mechanical properties of a clay-filled railway embankment. Seismic data were acquired bimonthly from July 2013 to November 2014 along the crest of a heritage railway embankment in southwest England. For each acquisition, the collected data were first processed to obtain a set of Rayleigh-wave dispersion and attenuation curves, referenced to the same spatial locations. These data were then analyzed to identify a coherent trend in their spatial and temporal variability. The relevance of the observed temporal variations was also verified with respect to the experimental data uncertainties. Finally, the surface wave dispersion data sets were inverted to reconstruct a time-lapse model of S-wave velocity for the embankment structure, using a least-squares laterally constrained inversion scheme. A key point of the inversion process was constituted by the estimation of a suitable initial model and the selection of adequate levels of spatial regularization. The initial model and the strength of spatial smoothing were then kept constant throughout the processing of all available data sets to ensure homogeneity of the procedure and comparability among the obtained sections. A continuous and coherent temporal pattern of surface wave data, and consequently of the reconstructed models, was identified. This pattern is related to the seasonal distribution of precipitation and soil water content measured on site.