Armando José Leitão Cordeiro

Dr. Armando José Leitão Cordeiro

orcid

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 June 2019 in IEEE Transactions on Vehicular Technology
Verified
Journal Article
Closed access
VPVitor Fernão Pires
Vitor Fernão Pires
ACArmando José Leitão Cordeiro
Armando José Leitão Cordeiro
DFDaniel Foito
Daniel Foito
Fernando Alves da SilvaFernando Alves da Silva
Fernando Alves da Silva
Most fuel cell electric vehicles (FCEV) require wide voltage-gain DC DC converters to increase and equalize the relatively low voltage of fuel cell stacks with DC link bus or energy storage devices (ESD), such as supercapacitors or batteries. This paper proposes two new non-isolated DC-DC converters suitable for such applications, which can be extended to other electric vehicles as well. The proposed converters combine the main characteristics of both quadratic Boost and Ćuk converters, offering high step up voltage and control simplicity using only one ground referenced active power switch. Additionally, the proposed topologies present reduced voltage stress across the active power switch when compared to other Boost converters. Considerations about the design of the proposed converters will also be presented. Experimental results obtained using a laboratory prototype validate the effectiveness and feasibility of the proposed topologies and its suitability for fuel cell electric vehicles.

22 January 2023 in Energies
Verified
Journal Article
Open access
PDF file
VPVitor Fernão Pires
Vitor Fernão Pires
Armando PiresArmando Pires
Armando Pires
ACArmando José Leitão Cordeiro
Armando José Leitão Cordeiro
One of the major paradigm shifts that will be predictably observed in the energy mix is related to distribution networks. Until now, this type of electrical grid was characterized by an AC transmission. However, a new concept is emerging, as the electrical distribution networks characterized by DC transmission are beginning to be considered as a promising solution due to technological advances. In fact, we are now witnessing a proliferation of DC equipment associated with renewable energy sources, storage systems and loads. Thus, such equipment is beginning to be considered in different contexts. In this way, taking into consideration the requirement for the fast integration of this equipment into the existing electrical network, DC networks have started to become important. On the other hand, the importance of the development of these DC networks is not only due to the fact that the amount of DC equipment is becoming huge. When compared with the classical AC transmission systems, the DC networks are considered more efficient and reliable, not having any issues regarding the reactive power and frequency control and synchronization. Although much research work has been conducted, several technical aspects have not yet been defined as standard. This uncertainty is still an obstacle to a faster transition to this type of network. There are also other aspects that still need to be a focus of study and research in order to allow this technology to become a day-to-day solution. Finally, there are also many applications in which this kind of DC microgrid can be used, but they have still not been addressed. Thus, all these aspects are considered important challenges that need to be tackled. In this context, this paper presents an overview of the existing and possible solutions for this type of microgrid, as well as the challenges that need to be faced now.

4 September 2017 in IEEE Transactions on Industry Applications
Verified
Journal Article
Closed access
VPVitor Fernão Pires
Vitor Fernão Pires
DFDaniel Foito
Daniel Foito
ACArmando José Leitão Cordeiro
Armando José Leitão Cordeiro
Energy storage devices are essential to provide voltage and frequency stability in renewable energy sources, such as solar and wind. Due to operational requirements of distributed generation systems, energy storage devices like batteries and supercapacitors need bidirectional dc-dc converters to allow charge or discharge exchange according with the necessary conditions. In this paper, a new nonisolated bidirectional quadratic converter characterized by high voltage gain in both step-down (Buck) and step-up (Boost) operation modes is proposed. In addition to the wide conversion range, it presents continuous input and output current and reduced charging/discharging ripple. All these features allow an optimized operation between the dc bus and storage devices. The operation principle of the proposed converter in both condition modes (step-down and step-up), the converter design, as well as the theoretical analysis in different conditions will be discussed. Finally, the performance of the proposed converter is confirmed through simulation and experimental results.

5 January 2016 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
VPVitor Fernão Pires
Vitor Fernão Pires
ACArmando José Leitão Cordeiro
Armando José Leitão Cordeiro
DFDaniel Foito
Daniel Foito
Joao MartinsJoao Martins
Joao Martins
This paper presents a three-phase multilevel quasi-Z-source inverter (qZSI) topology operating in normal and fault-tolerant operation mode. This structure is composed by two symmetrical quasi-Z-source networks and a three-phase T-type inverter. Besides the intrinsic advantages of multilevel voltage source inverters, the proposed structure is also characterized by their semiconductor fault tolerance capability. This feature is only obtained through changes on the modulation scheme after the semiconductor fault and does not require additional extra-phase legs or collective switching states. In certain fault types, the reduction of the output power capacity will be compensated by the boost characteristic of the qZSI. The fault-tolerant behavior of the proposed topology is demonstrated by several simulation results of the converter in normal and fault condition. To validate the characteristics of this multilevel qZSI, an experimental prototype was also built to experimentally confirm the results.

26 October 2021 in IEEE Access
Verified
Journal Article
Open access
VPVitor Fernão Pires
Vitor Fernão Pires
ACArmando José Leitão Cordeiro
Armando José Leitão Cordeiro
DFDaniel Foito
Daniel Foito
Fernando Alves da SilvaFernando Alves da Silva
Fernando Alves da Silva
This paper introduces a new topology for a DC-DC converter with bipolar output and high voltage gain. The topology was designed with the aim to use only one active power switch. Besides the bipolar multiport output and high voltage gain this converter has another important feature, namely, it has a continuous input current. Due to the self-balancing bipolar outputs, the proposed topology is suitable for bipolar DC microgrids. Indeed, the topology balancing capability can achieve the two symmetrical voltage poles of bipolar DC microgrids. Furthermore, it is possible to create a midpoint in the output of the converter that can be directly connected to the ground of the DC power supply, avoiding common-mode leakage currents in critical applications such as transformerless grid-connect PV systems. The operating principle of the proposed topology will be supported by mathematical analysis. To validate and verify the characteristics of the presented topology, several experimental results are shown.

1 November 2018 in Solar Energy
Verified
Journal Article
Closed access
VPVitor Fernão Pires
Vitor Fernão Pires
ACArmando José Leitão Cordeiro
Armando José Leitão Cordeiro
DFD. Foito
D. Foito
Fernando Alves da SilvaFernando Alves da Silva
Fernando Alves da Silva