This study aims to enhance the flame retardant efficiency and thermal stability of low density polyethylene (LDPE) by using halogen‐free inorganic additives. To prepare the highly loaded flame retardant polymer composites, LDPE melt mixes with magnesium hydroxide and magnesium carbonate at different weight ratios using a twin‐screw extruder. The composites are characterized by thermogravimetric analysis, crystallinity degree, tensile strength, morphological analysis, limiting oxygen index and UL‐94 vertical burning test. An optimum MH/MC weight ratio of 60/40 provides satisfactory composite properties with increased maximum thermal degradation temperature from 472.3 to 483.5°C, the highest LOI value of 32.5% and a UL‐94 V‐0 rating without melt dripping. The homogeneity of this composite is improved by using a polymeric compatibilizer, MAH‐g‐PE and an enhancement in tensile strength, elongation at break and elastic modulus values of 33.68%, 33.02% and 23.55%, respectively, are obtained. In order to create synergism between the flame retardant additives, 1, 3 and 5 wt% zinc borate is added to the composite system. The incorporation of 5 wt% ZB causes a significant delay in the thermal decomposition of MH with an improvement of 51.8°C in maximum degradation temperature. This composite also exhibits a satisfactory flame retardant grade with a UL‐94 V‐0 rating.
In this study, a series of covalently crosslinked, L-lysine based poly(beta-aminoester urethane) (LPBAEU) networks with good biodegradability and pH sensitivity was reported. The effect of hydrophilic/hydrophobic characteristics and diacrylate/amine molar ratio on the structure, swelling and degradation behaviour of the networks was investigated. The water transport mechanism and dynamic swelling behavior of the LPBAEU networks were strongly affected by medium pH, and swelling amounts up to 252.2% and 148.7% were observed at pH 5.6 and pH 7.4, respectively. It was found that water diffusion within the networks followed a non-Fickian mechanism. The LPBAEU network with the highest diacrylate/amine molar ratio exhibited the highest tensile strength and Young's modulus. In vitro mass losses of networks showed that the degradation rate of LPBAEU networks can be adjusted from 4 to 14 days. LPBAEU networks also supported loading of doxycycline hyclate (DH) and in vitro release studies demonstrated that release of DH from the networks was substantially hindered in the neutral pH environment, with 20.9–56.2% DH release, whereas DH release was accelerated under mild acidic conditions, with a release percentage of 36.6–99.6%. The release data were fitted to different mathematical models and the obtained results confirmed that these networks released DH in a non-Fickian mechanism. The results of this research support the idea that pH-responsive LPBAEU networks may find potential applications in local drug delivery.
3 February 2022 in Journal of Macromolecular Science, Part A
This study revealed the facile preparation of graphene oxide (GO) containing sodium alginate (SA) and hydroxyethyl cellulose (HEC) hydrogel beads that could be used as a low-cost and environmentally friendly bio-adsorbent for the removal of crystal violet (CV). The thermogravimetric analysis (TGA) and absorbency under load (AUL) test results demonstrated that the thermal stability and mechanical strength of SA-HEC hydrogel beads were enhanced by the existence of GO. The SA-HEC/GO bio-adsorbents displayed superior adsorption capability toward cationic CV dye molecules and the adsorption capacity increased from 123.16 mg g−1 to 312.72 mg g−1 at pH 5 by incorporation of 1 wt% GO. The CV adsorption is well-described by pseudo-second-order model and was mainly controlled by intra-particle diffusion. Also, the Langmuir and Temkin isotherm models confirmed the physical monolayer adsorption of CV. The calculated thermodynamic parameters such as Gibbs free energy (ΔG°), enthalpy (ΔH°) and entropy (ΔS°) indicated that the adsorption of CV onto SA-HEC/GO bio-adsorbents was spontaneous and it was favored at high temperatures. The bio-adsorbent retained its ability to adsorb CV with a removal efficiency of 79.4% for up to six cycles. Graphical Abstract
Poly(N-isopropylacrylamide) (P(NIPAAm)) hydrogels were prepared by free-radical polymerization with biodegradable poly (β-amino ester) (PBAE) crosslinkers at 1 wt% and 3 wt% ratio, and compared with conventional N,N′-methylene bisacrylamide (MBA)-crosslinked hydrogel. The influence of the type, molecular weight, and diacrylate/amine ratio of the crosslinker on the crosslink density, compressive strength, and swelling and biodegradation behavior of the hydrogels was investigated. The hydrogels synthesized with lower molecular weight PBAE crosslinkers showed higher crosslinking degrees and compressive strength and lower swelling ratios. To reveal the controlled release behavior of the fertilizer, KNO3 was used as the model, and its loading and release behavior from these hydrogels was also examined. The N/T5/1 sample with 1.5/1.0 diacrylate/amine molar ratio and 1 wt% PBAE ratio demonstrated the most controlled release of KNO3 with 66.9% after 18 days in soil. In addition, the hydrogel with the porosity of 71.65% and crosslinking degree of 2.85 × 10−5 mol cm−3 showed a swelling ratio of 69.44 g/g, biodegradation rate of 23.9%, and compressive strength of 1.074 MPa. Thus, it can be concluded that the new designed biodegradable P(NIPAAm) hydrogels can be promising materials as nitrate fertilizer reservoirs and also for controlled fertilizer release in soil media for agricultural applications.