Malaysia is anticipating an increase of 68.86% in CO2 emission in 2020, compared with the 2000 baseline, reaching 285.73 million tonnes. A major contributor to Malaysia’s CO2 emissions is coal-fired electricity power plants, responsible for 43.4% of the overall emissions. Malaysia’s forest soil offers organic sequestration of 15 tonnes of CO2 ha−1·year−1. Unlike organic CO2 sequestration in soil, inorganic sequestration of CO2 through mineral carbonation, once formed, is considered as a permanent sink. Inorganic CO2 sequestration in Malaysia has not been extensively studied, and the country’s potential for using the technique for atmospheric CO2 removal is undefined. In addition, Malaysia produces a significant amount of solid waste annually and, of that, demolition concrete waste, basalt quarry fine, and fly and bottom ashes are calcium-rich materials suitable for inorganic CO2 sequestration. This project introduces a potential solution for sequestering atmospheric CO2 inorganically for Malaysia. If lands associated to future developments in Malaysia are designed for inorganic CO2 sequestration using demolition concrete waste, basalt quarry fine, and fly and bottom ashes, 597,465 tonnes of CO2 can be captured annually adding a potential annual economic benefit of €4,700,000.
Amongst the strategies applicable for CO2 capture and sequestration, the adsorption process has a high potential to be applied as an alternative CO2 separation strategy as it offers large adsorption capacity, requires low energy for regeneration with economical equipment cost, prevents corrosion problems, and provides ease of applicability. Inspired by the most applicable amine-based chemical absorption for CO2 capture, the modification of adsorbent by amine was first considered and then investigated. This study introduces kenaf (Hibiscus Cannabinus L.) as a potential low-cost material in evaluating the effect of amine functional group concentrations on CO2 adsorption capacity. Monoethanolamine (MEA) and tetraethylenepentamine (TEPA) were impregnated on kenaf via a wetness impregnation method to achieve the aim. The ratios of amine to kenaf were varied at 1:2, 7:10, 1:1, 2:1, 5:1, 7:1, and 10:1. Then, the prepared amine-modified kenaf core sorbent was characterized using different morphology and structural characterization techniques such as a field emission scanning electron microscope (FESEM) analyzer and Fourier transform infrared (FTIR) spectroscopy. Results obtained through the analyses showed that amine (MEA and TEPA) were successfully impregnated on the kenaf core surfaces, and that amine concentrations have a significant effect on the morphological structures of the kenaf core support. The study on CO2 adsorption capacity was conducted in a pressure swing adsorption system (PSA). Results revealed that the highest CO2 adsorption capacity for MEA-modified kenaf adsorbent was achieved at an amine to kenaf ratio of 1:1 (2.070 mmol/g), while for TEPA-modified kenaf adsorbent at a ratio of 2:1 (2.086 mmol/g). The study on the effect of amine concentration on kenaf adsorbent is beneficial in introducing kenaf as a sorbent in capturing CO2.
The increasing of carbon dioxide (CO2) emission has become a major concern in averting the global warming effect. Prior to the established adsorption process in carbon capture and storage technology (CCS), the development towards potential bio-modified adsorbent had been extensively studied by impregnating monoethanolamine (MEA) on the bio-sorbent surface, as to increase the porosity of the raw sorbent towards enhancement in capturing CO2. As been recognized by Kyoto Protocol, kenaf (Hibiscus Cannabinus L.) is an eco-friendly industrial organic material that could overcome global warming issues due to its distinctive properties such as low density, highly porous, renewable, cheaper, and abundantly available compared to other organic or commercial adsorbents. Thus, kenaf as bio-sorbent material was used in this study with chemical modification done to evaluate its properties enhancement for CO2 adsorption enhancement. In the previous study, MEA has been proved as a good solvent to be impregnated into kenaf sorbent as it improved the adsorptive capacity by 16%. Therefore, this study focused on the evaluation on the porosity enhancement by impregnated MEA on kenaf sorbent at difference impregnated temperatures. The pressure drop across the modified sorbents using porosimeter was determined as to further evaluate on the porosity effect. Three different impregnation temperatures; 20, 27 and 40°C at 1:1 kenaf to MEA concentration ratio were evaluated. All samples were analyzed for the elemental composition to prove the successful of impregnated amine functional group (N-H). Through the porosimeter, it showed that the pressure drop across the modified kenaf-MEA had increased as higher temperature impregnated were used. The porosity of the modified sorbent evaluated had also increased proportionally to the pressure drop. The adsorbent experienced large pressure drop as more gas diffuses within the available void spaces in the kenaf sorbent. The enlargement of the porous media on the kenaf surface was due to the impregnated of amine functional group, thus increases the pore volume of the sorbent. This also agreed to the Boyle’s Law of Gas Expansion Method. From the study, it showed that the modified kenaf-MEA at 40°C impregnation temperature had the highest porosity of 58.6 with a pressure drop of 2.93 bar. This result indicated that the improvement of porosity was achieved by modification of kenaf sorbent at a high impregnated temperature.
1 February 2021 in IOP Conference Series: Materials Science and Engineering
In supporting the industrial kenaf plan developed by Malaysian government, this research has extended the use of kenaf as a sorbent to investigate its reliability for hydrogen adsorption system. In satisfying the objective, the effect of impregnation time and the effect of nickel nitrate concentration on hydrogen adsorption has been studied. In addition, to study the adsorption and desorption capability of the modified kenaf on hydrogen adsorption, the regeneration study was also accounted. The kenaf core with the range of particle size in between 300-500µm has been modified through the physicochemical modification by experiencing the carbonization and activation process prior to be impregnated in nickel nitrate solution (Ni(NO3)2). The morphological and elemental studies on the modified-kenaf sorbent have been done with the helped of Variable Pressure Scanning Electron Microscopy (VPSEM) and Energy Dispersive X-Ray (EDX) analyser, respectively. The hydrogen adsorption using the hydrogen adsorption system was controlled at the pressure of 5 bar. The results show that the modified-kenaf sorbent able to improve the hydrogen adsorption as compared to the unmodified-kenaf sorbent. Based on the morphological analysis, the modified-kenaf sorbent contain more micropores compares to the unmodified-kenaf sorbent which help in the adsorption capacity. Besides, the modified-kenaf sorbent has potential to be reused with minimum pressure drop of only 0.207 and 0.109 bar up to second regeneration cycles. This study has revealed that the modified-kenaf material has high capability to be used as hydrogen adsorbent and can be competitive technology over the existing current hydrogen storage technology.