Chronic foot ulcers are the leading cause of prolonged hospitalization and loss of social participation in people with diabetes. Conventional management of diabetic foot ulcers (DFU) is associated with slow healing, high cost, and recurrent visits to the hospital. Currently, the application of autologous lipotransfer is more popular, as the regenerative and reparative effects of fat are well established. Herein we report the efficacy of minimally manipulated extracellular matrix (MA-ECM) prepared from autologous homologous adipose tissue by using 3D bioprinting in DFU (test group) in comparison to the standard wound care (control group). A total of 40 subjects were screened and randomly divided into test and control groups. In the test group, the customized MA-ECM was printed as a scaffold from the patient autologous fat using a 3D bioprinter device and applied to the wound directly. The control group received standard wound care and weekly follow-up was done for all the patients. We evaluated the efficacy of this novel technology by assessing the reduction in wound size and attainment of epithelialization. The patients in the test group (n = 17) showed complete wound closure with re-epithelialization approximately within a period of 4 weeks. On the other hand, most of the patients in the control group (n = 16) who received standard wound dressings care showed a delay in wound healing in comparison to the test group. This technique can be employed as a personalized therapeutic method to accelerate diabetic wound healing and may provide a promising potential alternative approach to protect against lower foot amputation a most common complication in diabetes.

Adipose tissue is an abundant source of extracellular substances that support the tissue repair process. This pilot study was carried out to determine the efficacy of 3D-bioprinted autologous adipose tissue grafts on diabetic foot ulcers (DFUs), with fibrin gel used to stabilise the graft. This was a single-arm pilot study in a tertiary hospital that provides diabetic wound care services. A total of 10 patients with a DFU were enrolled, and the primary endpoint was complete healing within 12 weeks. The secondary endpoints were wound size reduction, time to healing, and adverse events. Seven out of ten patients showed complete healing of their DFU within 12 weeks (at 2, 4, 5, 10, and 12 weeks, respectively). The wound size reduction rate was significantly and progressively reduced over time. According to our data, autologous adipose tissue grafting using a 3D bioprinter, with the addition of fibrin gel that acts as a scaffold, promotes wound healing with high-quality skin reconstruction. Throughout this study period, no adverse events were observed.

Numerous studies have demonstrated the various properties of micronized adipose tissue (MAT), including angiogenic, anti-inflammatory, and regenerative activities, which can be helpful in wound healing. This exploratory clinical trial aimed to report the efficacy and safety of MAT niche for treating diabetic foot ulcers. Twenty subjects were randomly divided into MAT niche treatment (n = 10) and control groups (n = 10). All patients were followed up weekly for 16 weeks. We evaluated the efficacy of the MAT niche treatment by assessing the (1) reduction in wound area after 4 weeks and (2) percentage of patients who achieved complete wound closure after 16 weeks. All possible adverse events were recorded. The wound area was reduced by 4.3 ± 1.0 cm² in the treatment group and by 2.0 ± 1.1 cm² in the control group (p = 0.043). Complete wound healing was achieved after 16 weeks in eight out of 10 patients (80%) in the treatment group and three out of six (50%) in the control group (p = 0.299). No serious adverse events related to MAT niche treatment were observed. Although the present study’s findings do not support the use of this therapy to treat foot ulcers of patients with diabetes owing to the small number of patients included and the absence of statistical significance, the results of this pilot preliminary study are promising in that MAT niche autografts may offer the possibility of a simple and effective treatment for diabetic ulcers. Further follow-up studies with a larger number of patients are required to validate our findings.

Background: An autologous minimally manipulated homologous adipose tissue (AMHAT) fabricated using three-dimensional (3D) bioprinting has shown potential in the treatment of diabetic foot ulcers and other chronic wounds. Methods: This study assessed the efficacy of AMHAT fabricated using 3D bioprinting for treating skin defects after a wide excision of skin cancer lesions where primary closure was not feasible. A total of 10 consecutive patients were included. The wounds were photographed and analyzed using AI, and the fat tissue harvested from the lower abdomen was processed into an AMHAT patch using a 3D bioprinter. The wound area was measured weekly until complete wound closure was achieved. Results: The area of the skin defects ranged from 1.77–6.22 cm², averaging 2.72 cm². Complete closure was achieved in 3–5 (average, 4.2) weeks. The residual area decreased from 52% after 1 week to 3% after 4 weeks. The scar appearance was esthetically favorable, with one patient showing mild nostril asymmetry. Furthermore, patient-reported outcome evaluation using the Japanese version of SCAR-Q for postoperative scars showed a very high level of satisfaction. Conclusions: The 3D bioprinted AMHAT accelerates wound healing with minimal scarring, offering an important option for skin defects where esthetics are a priority.

Diabetic foot ulcers have a significantly negative impact on patients and are highly prone to contamination, which can lead to amputation. The best possible wound management treatment was essential for diabetic foot ulcers. However, since 4D bio printing is the best way to recapitulate complex and functional human tissue and organ, we have developed the therapeutic 4D bio printer called INVIVO to use in skin regeneration. To find advanced treatment method particularly for wound healing, we tested our own 4D bio printing system with autologous fat tissue for DFU treatment. The extracellular matrix (ECM) derived from Nano-fat consisting of supportive proteins, growth factors and cytokines, has been reported as an important player to provide efficient 3D environments during cell proliferation and differentiation. In the clinical study, we printed autologous ECM (MA-ECM) with bio-inks to apply onto the chronic wound site. Most of DFU patients showed significant reduction of wound size with distinct epithelization only after a week treatment. Therefore, we suggest 4D bio printing system with MA-ECM as an alternative method for dressing materials that successfully promote the mechanism of skin reconstruction for DFU treatment. Reduction in size of wound was measured using ImageJ NIH software and almost all the subjects revealed complete closure of wound maximum of 2∼5 weeks post MA-ECM membrane application. The present study provided a significantly higher healing rate of the subjects and the primary outcome of our study complete epithelization with wound closure was achieved. The autologous fat by nature is loaded with adipocytes and growth factors which could have played a vital role in the healing of non-healing diabetic wounds. Therefore, we suggest 4D bio printing system with MA-ECM as an alternative method for chronic wound healing that successfully promote the mechanism of skin reconstruction for DFU treatment. Disclosure: J. Kim: None.