The electron transport layer (ETL) plays a crucial role in solar cell technology, particularly in perovskite solar cells (PSCs), where nanostructured TiO2 films have been investigated as superior ETLs compared to compact TiO2. In this study, we explored the nanocolumnar growth of TiO2 in the anatase phase for bilayer thin films by DC reactive magnetron sputtering (MS) technique and glancing-angle deposition (GLAD). For the growth of the compact TiO2 layer, it was found that the crystalline quality of the films is strongly dependent on the sputtering power, and the samples deposited at 120 and 140 W are those with the best crystalline quality. However, for the nanocolumnar layer, the reactive atmosphere composition determined the best crystalline properties. By optimizing the growth parameters, the formation of TiO2 nanocolumns with a cross-sectional diameter ranging from 50 to 75 nm was achieved. The average thickness of the films exceeded 12.71 ± 0.5 µm. All nanostructured films were grown at a constant GLAD angle of 70°, and after deposition, the measured inclination angle of the nanocolumns is very close to this, having values between 68 and 80°. Furthermore, a correlation was observed between the quality of the initial layer and the enhanced growth of the TiO2 nanocolumns. All bilayer films are highly transparent, allowing light to pass through up to 90%, and present a band gap with values between 3.7 and 3.8 eV. This article offers the experimental parameters for the fabrication of a nanocolumnar TiO2 using the magnetron sputtering technique and the glancing-angle deposition configuration.
Recently, there is a renewed interest from the scientific community in the study of the electrical signal generated by plants due to its wide range of applications in agriculture, for example, environmental monitoring, detection of pests, diseases in crops, etc. Therefore, the aim of this work is to characterize the electrical signal of Aloe vera var. chinensis by using non-parametric and parametric signal analysis techniques, in order to extract some fundamental features which could be used in the design of a bio-dosimeter. Non-parametric analysis of the signal was carried out in the time, frequency, and time-frequency domains, using the short-time Fourier transform (STFT) and the wavelet transform in order to determine the different characteristics and frequency changes over time. Parametric analysis was then performed by using auto-regressive (AR) models for signal prediction and modeling, and in this case the coefficients of the model will be considered as fundamental features to be extracted. It has been identified that the majority of the signal energy is found in low frequencies, possibly associated with physiological processes or changes in the environment. Subsequently, some metrics like mean squared error (MSE), mean absolute error (MAE), and coefficient of determination (R2) were used in order to establish the capability of modeling the signal in its totality, considering that it is affected by the abrupt changes present in the signal. In this way, the relevance of combining both analyses is discussed in order to take their advantages for the benefit of the compression and feature extraction of the electrical signal of Aloe vera var. chinensis. This analysis allows the Aloe vera var. chinensis plant to be used for environmental monitoring, pest and disease detection in crops, or in a pattern recognition and signal classifier systems.
Through the electrical signal generated by a plant, it is possible to identify water stress, pests on its roots, a sick plant, or even identify the optimal growing conditions. In particular, the optimal growing conditions in the strawberry plant can be identified by its electrical signal, which can be useful to increase its production, since its fruits are in high demand for human consumption. Therefore, the aim of this pilot study is to use machine learning techniques to characterize the electrical signal of optically stimulated hydroponic strawberries, in order to identify the optimal growing conditions. The electrical signal was monitored using a home-made electronic system, based on Arduino. The principal result obtained shows that red light is the most informative feature in the random forest (RF) model, demonstrating superior performance in minimizing misclassification rates. In contrast, the support vector machine (SVM) model exhibited increased sensitivity to data variations, resulting in elevated misclassification rates. The feature importance analysis shows that the variable red light contributes 35% to the predictive capability of the model. Natural light and green light follow with approximately 25% each, while the contribution of yellow light is negligible at 15%. Finally, in this exploratory study, it would appear that the electrical signal from the plant is sensitive to specific light conditions, with red light being most impactful.
24 December 2024 in Nuclear Engineering and Technology
P-type Ag-N dual acceptor doped ZnO thin films with long electrical stability were deposited by DC magnetron reactive co-sputtering technique. After deposition, the films were annealed at 400 °C for one hour in a nitrogen-controlled atmosphere. The deposited films were amorphous. However, after annealing, they crystallize in the typical hexagonal wurtzite structure of ZnO. The Ag-N dual acceptors were incorporated substitutionally in the structure of zinc oxide, and achieving that; the three samples presented the p-type conductivity in the ZnO. Initial electrical properties showed a low resistivity of from 1 to 10−3 Ω·cm, Hall mobility of tens cm2/V·s, and a hole concentration from 1017 to 1019 cm−3. The electrical stability analysis reveals that the p-type conductivity of the ZnO:Ag,N films is very stable and does not revert to n-type, even after 36 months of aging. These results reveal the feasibility of using these films for applications in short-wavelength or transparent optoelectronic devices.