Because the operating speed of current mechanical maize hole seeders is low and their ability to adapt to the seed is poor, an active clamping-type precision hole planter for corn was designed. Here, we explain its structural composition and working principle. According to the maize kernel size, the combination of hole parameters is based on the principle of virtual work on analyzing the seed extraction disc assembly’s static mechanical model. The model was imported into the ADAMS simulation for validation and the parameters and ranges affecting the seed-filling performance were identified. By further analyzing the results of the coupled ADAMS–EDEM simulation, the “arching” process of the seeds during leakage charging was revealed, and an arch-breaking method was proposed with the help of a swinging seed-collecting slider. The speed of the hole planter, the diameter of the outer edge of the gravity ring, and the angle of the block installation were used as test factors. The Box–Behnken center-combination simulation test was conducted using the sowing pass index, re-seeding index, and missed sowing index as evaluation indices. The experimental results show that the optimal parameter combination was as follows: gravity ring = 174.3 mm, stopper installation angle = 131.9°, and hole seeder speed = 85.2 rpm. At this time, the qualified seeding index was 94.53%, the multiple indices were 4.30%, and the leakage index was 1.18%. Under these conditions, the row seeding performance bench test was conducted to obtain the qualified seeding index of the hole seeder, which was 93.36%, while the multiple indices were 5.20% and the leakage index was 1.44%, which satisfied the agronomic requirements of precision seeding. This provides a theoretical reference for mechanical seeding methods for irregular seeds, as well as a basis for the research and development of maize precision sowing machinery and equipment.
We have combined the theory of bulk dynamics and the agronomic requirements of precision sowing with the aim of resolving the technical problems of poor seed mobility and the difficulty in controlling suction posture, which leads to an increase in the leakage rate and a reduction in seed qualification index scores. In this study, a vibrationally tuned directional seed supply method and system are proposed. We carried out a force analysis of seeds, constructed kinematic equations for seeds and seed boxes to specify the state of the seed motion, and determined the structural parameters and the range of structural parameters that affect the seed suction posture. In addition, we coupled the ADAMS-EDEM simulation of the motion process of the seed and seed boxes and analyzed the vibrational tuning process of the seeds and the angle of inclination of the bottom surface of the seed box. The speed of the eccentric wheel and the eccentric distance were used as test factors. Three-factor and three-level Box–Behnken central combination testing with a single-grain rate, multiple-grain rate, and cavity rate were used as response indicators. Mathematical models were obtained between the experimental factors and the response indicators. Multi-objective optimization of mathematical regression models was carried out with Design-Expert 10.0.4 software. The optimal parameter combination obtained was a tilt angle of 14.27°, an eccentric wheel speed of 4.48 rad/s, and an eccentricity of 1.94 mm. The rate of single grains was 90.75%, the rate of multiple grains was 3.63%, and the rate of cavities was 5.62%. In bench performance tests, using an angle of inclination of 14°, the speed of the eccentric wheel was 4.50 rad/s and the eccentricity was 2 mm. The mean value of the single-grain rate was 89.28%, the mean value of the multiple-grain rate was 3.89%, and the mean value of the cavity rate was 6.83%. The test error was within permissible limits, and reliable results were achieved for parameter optimization. The results met the technical requirements for precision sowing. The results of the study can provide academic references for theoretical research on the methodology of posturing and directional seed supply. They can also provide ideas for the design and development of seed supply systems for precision sowing machinery.
Agricultural mulch waste that is mechanically recycled has a high resource value. It has been found that the mulch is tightly entangled in the crop straw, forming a knotted feature that prevents further resource utilization. Traditional cutting tools were found to be ineffective in breaking up the knotted feature. In response to the above problems, a sliding cutting device for mechanically recovered mulch waste was proposed and built. The structure of the device and key components were designed and analyzed. A three-factor five-level orthogonal test was conducted and regression variance analysis was performed with the Central Composite Design (CCD) module in Design expert 8. The relationship model was constructed between the test factors such as supporting motor speed a, cutting-support rotation speed ratio b, and cutting edge angle c and the response indicators such as film breakage rate y1 and knotted feature removal rate y2. The influence law between each key parameter with its significant interaction and the waste crushing effect was analyzed, and the optimum combination of parameters of the crushing device were obtained. Under the same conditions, the errors between the physical test values and the model prediction values of the two response indicators were 2.17% and 3.52%, respectively, indicating that the verification test results were basically consistent with the model prediction results.
The mechanized resource utilization of domestic waste is the development trend in the field of waste treatment. The difficulty of bag breaking and the easy entanglement of domestic waste are the factors restricting the mechanization of waste separation and recycling. In response to the above problems, an internal blowing anti-tangle bag-breaking device for domestic waste was developed by combining the arc-type cutter and the internal flow field of the rotary. In addition, the motion trajectory of the cutters and the support rods were theoretically analyzed, as well as the force during the bag-breaking process of domestic waste. A three-factor, five-level orthogonal test was carried out to complete the regression ANOVA, and a relationship model was constructed between the test factors such as the cutting–support speed ratio, the center distance, the inlet flow rate and the response indicators such as the bag film length–perimeter ratio and bag film winding specific gravity. The key parameters and their significant interactions with the bag-breaking efficiency were analyzed to obtain the optimal combination of parameters for the device. Under the same conditions, the errors between the physical test and model predictions for the two response indicators were 5.46% and 7.90%, respectively, indicating that the verification test results were basically consistent with the model prediction results.