Bo Yang

Bo Yang


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 March 2023 in Materials
Verified
Journal Article
Open access
PDF file
GZGuoqing Zhang
Guoqing Zhang
WLWeihong Lu
Weihong Lu
XWXiaocong Wu
Xiaocong Wu
BYBo Yang
Bo Yang
YTYapeng Tan
Yapeng Tan
Junsheng WangJunsheng Wang
Junsheng Wang
With the aim of obtaining a refining flux that is stable and provides effective refining of aluminum melt, a new strategy of designing the flux composition has been proposed. Ten fluxes were designed, by selecting ten molten salt compounds according to their thermophysical parameters, physical properties, and thermodynamic analysis. The melting points of the ten fluxes, and the phases transformation of the fluxes after melting, were studied by DSC and XRD, respectively. The contact angles between four groups of fluxes and alumina at refinement temperatures were studied, and the effect of refinement was characterized by a metallographic microscope. The process of the fluxes removing inclusions and degassing was analyzed thermodynamically. The research findings indicate that flux #10 (11.0 wt.%NaF, 29.5 wt.%NaCl, 46.5 wt.%Na2CO3, 3.0 wt.%CaF2, 10.0 wt.%Na3AlF6) has a melting point (562.2 °C) below the refining temperature. At the refining temperature (760 °C), flux #10 has the lowest contact angle, of 12.78°. In addition, compared to that of flux STJ–A3, currently used in practice, flux #10 has a better refining effectiveness, with the pores and inclusions content of the sample being reduced to 1.11% from 2.96%.

26 January 2023 in Metals
Verified
Journal Article
Open access
PDF file
BYBo Yang
Bo Yang
WLWeihong Lu
Weihong Lu
GZGuoqing Zhang
Guoqing Zhang
YTYapeng Tan
Yapeng Tan
XWXiaocong Wu
Xiaocong Wu
MCMao Cheng
Mao Cheng
The kinetic mechanism of hydrogen absorption of the AA6111 alloy melt in different melting environments, and the in-situ real-time observation of the oxide film structure during the hydrogen absorption process were studied. The results show that the hydrogen absorption process of the aluminum alloy melt is related to the melting environment and the oxide film on the melt surface. The hydrogen content in the melt increases with the extension of time when the melting environment humidity and temperature are constant. The initial hydrogen content is also higher and the hydrogen absorption capacity of the melt is larger when the melting temperature is constant with an increasing melting environment humidity. The oxide film will fold over on itself and become porous, due to the change in the structure of the melt surface during heating. The surface of the melt is similar to the double-oxide-film defect hydrogen absorption carrier, which leads to the aggravation of hydrogen absorption. Hydrogen absorption kinetic equations for the aluminum alloy melt under different melting environments are obtained based on the experimental results.

13 March 2023 in Metals
Verified
Journal Article
Open access
PDF file
YTYapeng Tan
Yapeng Tan
GZGuoqing Zhang
Guoqing Zhang
WLWeihong Lu
Weihong Lu
BYBo Yang
Bo Yang
ZTZhichao Tang
Zhichao Tang
LXLei Xiang
Lei Xiang
Aluminum and its alloy castings are used more and more widely, and it is particularly important to remove impurities in the alloy. According to the principle of bubble floatation for degassing aluminum melt, a new porous nozzle with controllable pores was developed, and a hydraulic simulation experimental device was studied with the nozzle. The effects of the particle size ratio of the coarse sand to fine sand and volume fraction of fine sand on the porosity of the porous nozzle were studied by orthogonal experiment, and permeability and compressive strength of the porous nozzle were used as test indicators to determine the optimal parameters of preparation for the porous nozzle. The optimal parameters are fine sand of 100 mesh, and fine sand of 50 wt.%, binder of 17.5 wt.%, pore-forming agent of 6 wt.%, and pressure of making sample of 5 MPa. The nozzle with optimal parameters was prepared and tested, and the permeability is 112.2 × 10−12 m2 and the compressive strength is 2.3 MPa. In addition, a physical model of gas transmission in the porous nozzle was proposed. With the increase in the proportion of fine sand, the permeability of the porous nozzle decreases, the compressive strength increases, and the calculated porosity increases. The hydraulic simulation of melt injection was carried out, and the mathematical model for calculating the bubble diameter of bubble floatation was formulated. The model shows that the bubble diameter increases with the increase in gas flow rate. The experiment shows that the prepared porous nozzle has the merits of a simple preparation process and low-cost, which is expected to degas aluminum melts.