The use of nano-additives in improving drilling fluid properties in order to meet the modern drilling process requirement is still being debated till date. In this study, nano bentonite and nano chemical additives are used to improve the rheological and filtration properties of drilling fluid using local and commercial bentonite. In the first part of this work, the feasibility of using Iraqi clay as a source of drilling fluid was investigated at 6, 10, 15 and 20wt% concentrations and mixed with nano commercial bentonite and nano Iraqi clay at 1, 2, 3, and 4wt% concentrations. The results showed that this addition did not improve the properties of drilling fluid and its quality in order to meet the API standards.In the second part, a commercial bentonite was used and mixed with nano commercial bentonite and nano chemical materials (MgO, TiO2, and graphene) at 0.005, 0.01, 0.05, 0.1, 0.2 and 0.4wt% concentrations. The results showed that nano commercial bentonite gives the same filtration behavior of graphene, whereas, the plastic viscosity, yield point and apparent viscosity were the same when using nano commercial bentonite, TiO2 and graphene. The best results were obtained with MgO addition, whereby the filter loss decreased to 35% with a higher value of yield point

A homemade N doped-TiO2 nanoparticle were used to degrade dibenzothiophene (DBT) in a model fuel flowing on a bench-scale glass-made falling film reactor irradiated by a xenon lamp that emitted visible light. The photocatalyst was immobilized on the glass sheet. EDS, SEM, and FT-IR techniques were utilized to identify the morphology of the N doped-TiO2 nanoparticles. Different operating parameters (e.g., N loading (0, 4, 5, and 6 wt%), light intensity (20, 40, and 60 W/m2), and pH (4, 7, and 10)) were investigated for their effect on the DBT degradation. The effect of the N loading on the wettability of the nano-TiO2 particles was also investigated. Experimental results revealed that the N loading did not affect the wettability characteristics of the nano TiO2 particles. Moreover, results showed that DBT conversion positively depends on N loading, light intensity (hv), and pH increase. The estimated optimal operating parameters were 5 wt% N loading, pH = 10, and hv = 40 W/m2 to ensure the best photo-oxidation efficiency of 91.4% after 120 min of operation. The outcomes of the present work confirmed the effective efficiency of the N-doped TiO2 nanoparticles irradiated by visible light for DBT degradation. Copyright © 2022 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0).

Among the several ways used in wastewater treatment, the photocatalysis process is a more novel and alternative process that is increasingly employed in recent years. This work aims to improve the performance of the photocatalyst process by using air bubbles in removing the BTEX from produced water as an indicator of process efficiency. The study also shows the effect of influencing factors (pH and residence time) on the photocatalysis process. The study was done in a rectangular column with dimensions of 200 mm width, 30 mm depth, and 1500 mm height. Commercial titanium oxide (TiO2) coated on a plate by the varnish was used as a source of the photocatalyst. The experiment was carried out under different values of gas flow rate (0-3 L/min) to evaluate its effect on the photocatalyst process, the effect of other variables of pH (3-11), and irradiation time (30-120) min was also studied. A new method of the coating was adopted by using an alumina plate with varnish as an adhesive. The characteristics results show that the coated plate has hydrophilic properties and that there is no significant change in the crystal structure of the TiO2 nanoparticles and the varnish before and after 60 h of the photocatalytic process, indicating that the plate is still effective after 60 h usage under different conditions. The results also show that the introduction of air bubbles enhances the removal efficiency of BTEX significantly and the best removal effectiveness of BTEX was 93% when pH = 5 after 90 min and 90% when pH = 3 after 120 min. The removal rate also reached 86% when pH = 7 after 120 min all at a flow rate of 3 L/min. The percentage of removal decreased at pH = 9 and 11, reaching 64% and 50%, respectively after 120 min and a flow rate of 3 L/min. Copyright © 2022 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0).

Drag reduction in turbulent flow may be significantly reduced by adding tiny quantities of fiber, polymer, and surfactant particles to the liquid. Different drag-reduction agents have proven to be effective in enhancing the flowability of the liquid when added. This study investigated the potential of decreasing the drag, turbulent flow, and pressure drop in horizontal pipe flow by using a mixture of modified xanthan gums (XGs). Xanthan gums are an environmentally friendly natural polymer complex. They can be extracted from xanthan gum plants and utilized to formulate different concentrations of complexes. The flowability of the xanthan gum was experimentally investigated in a 1-m-long pipe by using addition concentrations of 300 to 950 ppm, an inner diameter of 0.254 inches, and four different flow rates. The results revealed that the pressure drop was reduced considerably with an increase in the concentration of the additives. The mixture (xanthan gums plus water) resulted a favorable reduction in the pressure, which reached 65% at a concentration of 950 ppm. The results of the computational fluid dynamic simulation using the COMSOL simulator showed a change in the fluid velocity profiles, which became more parabolic. This occurred because of an increase in the mean fluid velocity due to the addition of the drag-reducing polymers.