Formic acid oxidation (FAO) is a typical anode reaction in fuel cells that can be facilitated by modulating its direct and indirect reaction pathways. Herein, PtAu bimetallic nanoparticles loaded onto Co and N co-doping carbon nanoframes (CoNC NFs) were designed to improve the selectivity of the direct reaction pathway for efficient FAO. Based on these subtle nanomaterials, the influences of elemental composition and carbon-support materials on the two pathways of FAO were investigated in detail. The results of fuel cell tests verified that the appropriate amount of Au in PtAu/CoNC can promote a direct reaction pathway for FAO, which is crucial for enhancing the oxidation efficiency of formic acid. In particular, the obtained PtAu/CoNC with an optimal Pt/Au atomic ratio of 1:1 (PtAu/CoNC-3) manifests the best catalytic performance among the analogous obtained Pt-based electrocatalysts. The FAO mass activity of the PtAu/CoNC-3 sample reached 0.88 A·mgPt−1, which is 26.0 times higher than that of Pt/C. The results of first-principles calculation and CO stripping jointly demonstrate that the CO adsorption of PtAu/CoNC is considerably lower than that of Pt/CoNC and PtAu/C, which indicates that the synergistic effect of Pt, Au, and CoNC NFs is critical for the resistance of Pt to CO poisoning. This work is of great significance for a deeper understanding of the oxidation mechanism of formic acid and provides a feasible and promising strategy for enhancing the catalytic performance of the catalyst by improving the direct reaction pathway for FAO.
Constructing a heterogeneous interface using different components is one of the effective measures to achieve the bifunctionality of nanocatalysts, while synergistic interactions between multiple interfaces can further optimize the performance of single-interface nanocatalysts. The non-precious metal nanocatalysts MoS2/NiSe2/reduced graphene oxide (rGO) bilayer sandwich-like nanostructure with multiple well-defined interfaces is prepared by a simple hydrothermal method. MoS2 and rGO are layered nanostructures with clear boundaries, and the NiSe2 nanoparticles with uniform size are sandwiched between both layered nanostructures. This multiple-interfaced sandwich-like nanostructure is prominent in catalytic water splitting with low overpotential for oxygen evolution reaction (OER) and hydrogen evolution reaction (HER) and almost no degradation in performance after a 20 h long-term reaction. In order to simulate the actual overall water splitting process, the prepared nanostructures are assembled into MoS2/NiSe2/rGO||MoS2/NiSe2/rGO modified two-electrode system, whose overpotential is only 1.52 mV, even exceeded that of noble metal nanocatalyst (Pt/C||RuO2~1.63 mV). This work provides a feasible idea for constructing multi-interface bifunctional electrocatalysts using nanoparticle-doped bilayer-like nanostructures.
Pt-based magnetic nanocatalysts are one of the most suitable candidates for electrocatalytic materials due to their high electrochemistry activity and retrievability. Unfortunately, the inferior durability prevents them from being scaled-up, limiting their commercial applications. Herein, an antiferromagnetic element Mn was introduced into PtCo nanostructured alloy to synthesize uniform Mn-PtCo truncated octahedral nanoparticles (TONPs) by one-pot method. Our results show that Mn can tune the blocking temperature of Mn-PtCo TONPs due to its antiferromagnetism. At low temperatures, Mn-PtCo TONPs are ferromagnetic, and the coercivity increases gradually with increasing Mn contents. At room temperature, the Mn-PtCo TONPs display superparamagnetic behavior, which is greatly helpful for industrial recycling. Mn doping can not only modify the electronic structure of PtCo TONPs but also enhance electrocatalytic performance for methanol oxidation reaction. The maximum specific activity of Mn-PtCo-3 reaches 8.1 A·m-2, 3.6 times of commercial Pt/C (2.2 A·m-2) and 1.4 times of PtCo TONPs (5.6 A·m-2), respectively. The mass activity decreases by only 30% after 2,000 cycles, while it is 45% and 99% (nearly inactive) for PtCo TONPs and commercial Pt/C catalysts, respectively.
Fuel cells are one of the promising energy-conversion devices due to their high efficiency and zero emission. Despite tremendous research works in past decades, there remains a tough challenge in realizing the commercial applications of fuel cell technologies. Therefore, the development of highly efficient and stable fuel cell electrocatalyst is the top priority for practical fuel cells. As we all know, the small-size nanoparticles always have high specific surface area, which can provide more active sites to enhance the catalytic activity, while the one-dimensional nanowires usually own high structural stability. It may provide a possibility for the design of a novel bimetal Pt-based alloy nanostructure by combining the structural superiority of both, which can maintain the high stability and maximize the catalytic activity at the same time. Driven by these purposes, a novel nanostructure constructed by Pt-Ni alloy nanoparticles with a one-dimensional chain structure was designed to balance the contradiction between the activity and stability due to the size effects (the smaller the size, the higher the activity, and the worse the stability of the nanocatalyst; and vice versa). Here, a simple one-step solvothermal method has been adopted to produce the novel nanostructures constructed by the chain-like Pt-Ni nanoparticles (Pt-Ni CNPs) with Pt-rich crystal faces and alloy nature. The structure, component and catalysis were investigated by the combination of X-ray diffraction, transmission electron microscopy, X-ray photoemission spectra, and electrochemical measurements. The results show that the as-synthesized Pt-Ni CNP is constructed from a nanowire (with a diameter of about 3 nm and a length of several hundred nanometers) and the nanoparticles (with an average diameter of about 10 nm). This nanostructure is cleverly integrated the structural advantages of one-dimensional nanowires and zero-dimensional nanoparticles, which can significantly enhance the catalytic activity and stability for the methanol oxidation reaction (MOR) in acidic environment. Specially, the mass activity and specific activity of as-prepared Pt-Ni CNPs are 5.7 and 7.6 times higher than those of the commercial Pt/C, respectively. After 1000 cycles of cyclic voltammetry (CV) measurement, Pt-Ni CNPs still retain 91.2% of the specific activity, while the commercial Pt/C undergoes a drastic loss of MOR activities, retaining only 4.4% of the initial activity. It is particularly noteworthy that this nanostructure of Pt-Ni CNP solves the problem of agglomeration of nanoparticle catalysts in the reaction, and provides a new approach to obtain Pt-based nanocatalysts with high catalytic activity and stability at the same time. Our finding will provide insight into more rational designs of Pt-based bimetallic nanocatalysts with one-dimensional architectures, which is expected to promote the further development and large-scale industrial application of the direct methanol fuel.
7 June 2022 in Journal of Physics D: Applied Physics
Fuel cells are highly efficient conversion devices to alleviate energy crisis and environmental pollution, but still encounter technical challenges to further improve catalytic efficiency of Pt-based electrocatalysts. In this work, PtNi multi-branched nanostructures (PtNi MBNs) were successfully prepared by a simple and economical one-step solvothermal method. The average diameter of the branches is about 9 nm, with numerous atom steps and Pt-rich surface. The prepared electrocatalyst shows excellent bifunctionality in acidic electrolytes, catalyzing both oxygen reduction reaction (ORR) and methanol oxidation reaction (MOR). The half-wave potential of 0.966 V for ORR is much higher than that of commercial Pt/C (0.931 V), and only decreases 14 mV after 8000 cycles. For MOR, the specific activity of PtNi MBNs is 18.1 A , better than that of commercial Pt/C (7.8 A ), indicating an optimal intrinsic activity. The remarkable bifunctionality of PtNi MBNs is attributed to the exposed electrochemical surface area, abundant atomic steps, and Pt-rich surface provided by the unique MBN. This facile preparation technique offers a promising application for designing high-performance electrocatalyst for acid direct methanol fuel cell in the future.