Recent studies have shown that enveloped viruses contained in airborne respiratory droplets lose infectability fastest at intermediate ambient relative humidities . However, the precise physicochemical mechanisms that generate such least-favorable conditions for the virus are not fully understood yet. Studying the evaporation dynamics of respiratory-like droplets in air experimentally and analytically, we reveal that at high , the salt dissolved in respiratory drops inhibits their evaporation indefinitely. Conversely, at low the drop evaporates leaving a porous solid residue, inside which virions may remain dormant for long times. We conclude that the optimal relative humidity for minimal infectability should coincide with droplets containing the maximum concentration of salt for longest periods of time.
An investigation of the pub prank ``beer tapping'' provides a better understanding of gas-driven eruptions that occur in carbonated beverages, as well as in volcanic environments.
The accurate description of the growth or dissolution dynamics of a soluble gas bubble in a super- or undersaturated solution requires taking into account a number of physical effects that contribute to the instantaneous mass transfer rate. One of these effects is the so-called history effect. It refers to the contribution of the local concentration boundary layer around the bubble that has developed from past mass transfer events between the bubble and liquid surroundings. In Part 1 of this work (Peñas-Lópezet al.,J. Fluid Mech., vol. 800, 2016b, pp. 180–212), a theoretical treatment of this effect was given for a spherical, isolated bubble. Here, Part 2 provides an experimental and numerical study of the history effect regarding a spherical bubble attached to a horizontal flat plate and in the presence of gravity. The simulation technique developed in this paper is based on a streamfunction–vorticity formulation that may be applied to other flows where bubbles or drops exchange mass in the presence of a gravity field. Using this numerical tool, simulations are performed for the same conditions used in the experiments, in which the bubble is exposed to subsequent growth and dissolution stages, using stepwise variations in the ambient pressure. Besides proving the relevance of the history effect, the simulations highlight the importance that boundary-induced advection has to accurately describe bubble growth and shrinkage, i.e. the bubble radius evolution. In addition, natural convection has a significant influence that shows up in the velocity field even at short times, although given the supersaturation conditions studied here, the bubble evolution is expected to be mainly diffusive.
The formation of vortex rings in negatively buoyant starting jets has been studied numerically for different values of the Richardson number, $\mathit{Ri}$ , covering the range of weak to moderate buoyancy effects ( $0\leq \mathit{Ri}\leq 0. 20$ ). Two different regimes have been identified in the vortex formation and the transition between them takes place at $\mathit{Ri}\approx 0. 03$ . The vorticity distribution inside the vortex ring after pinching off from the trailing stem as well as the total amount of circulation it encloses (characterized by the formation number, $F$ ) show different behaviours with the Richardson number in the two regimes. The differences are associated with the different mechanisms by which the head vortex absorbs the circulation injected by the starting jet. While secondary vortices are engulfed by the leading vortex before separating from the trailing jet in the weak buoyancy effects regime ( $0\lt \mathit{Ri}\lt 0. 03$ ), this phenomenon is not observed in the moderate buoyancy effects regime ( $0. 03\lt \mathit{Ri}\lt 0. 2$ ). Moreover it is shown that the formation number of a negatively buoyant vortex ring can be determined by considering that its dynamics are similar to that of a neutrally buoyant vortex but propagating with velocity corresponding to the negatively buoyant one. Based on this simple idea, a phenomenological model is presented to describe quantitatively the evolution of the formation number with the Richardson number, $F(\mathit{Ri})$ , obtained numerically. In addition, the limitations of different vortex identification methods used to evaluate the vortex properties in buoyant flows are discussed.
Besides being the favorite beverage of a large percentage of the population, a glass or bottle of beer is a test bench for a myriad of phenomena involving mass transfer, bubble-laden flows, natural convection, and many more topics of interest in Physical Chemistry. This paper summarizes some representative physical problems related to bubbles that occur in beer containers, pointing out their practical importance for the industry of beverage processing, as well as their potential connection to other processes occurring in natural sciences. More specifically, this paper describes the physics behind the sudden foam explosion occurring after a beer bottled is tapped on its mouth, gushing, buoyancy-induced motions in beer glasses, and bubble growth in stout beers.
Dip coating is a common technique used to cover a solid surface with a thin liquid film, the thickness of which was successfully predicted by the theory developed in the 1940s by Landau & Levich (Acta Physicochem. URSS, vol. 17, 1942, pp. 141–153) and Derjaguin (Acta Physicochem. URSS, vol. 20, 1943, pp. 349–352). In this work, we present an extension of their theory to the case where the dipping bath contains two immiscible liquids, one lighter than the other, resulting in the entrainment of two thin films on the substrate. We report how the thicknesses of the coated films depend on the capillary number, on the ratios of the properties of the two liquids and on the relative thickness of the upper fluid layer in the bath. We also show that the liquid/liquid and liquid/gas interfaces evolve independently from each other as if only one liquid were coated, except for a very small region where their separation falls quickly to its asymptotic value and the shear stresses at the two interfaces peak. Interestingly, we find that the final coated thicknesses are determined by the values of these maximum shear stresses.