P-type doping in selected areas of gallium nitride (GaN) using magnesium (Mg)-ion implantation and subsequent ultra-high-pressure annealing (UHPA) are investigated to improve the performance of vertical GaN power devices. UHPA allows a high-temperature process without decomposition of the GaN surface and virtually complete activation of the implanted Mg ions in GaN. In the present paper, we provide an overview of recent challenges in making UHPA more realistic as an industrial process. Instead of UHPA at more than 1400 °C for a short duration, prolonged UHPA at 1300 °C demonstrates a comparable acceptor activation of Mg-ion-implanted GaN. This can reduce the annealing pressure to approximately 300 MPa and enlarge the processable wafer diameter. The second challenge is controlling the doping profiles in the lateral and vertical directions. We demonstrate fine patterning of the p-type regions, which indicates the limited lateral diffusion of Mg through UHPA. However, controlling the vertical doping profile is challenging. The nitrogen vacancies formed by ion implantation reduce the effective acceptor concentration near the surface, which can be compensated for by sequential nitrogen ion implantation. Defect-assisted Mg diffusion to the deeper region causes a redistribution of the Mg atoms and should be considered in the design of a device. Such anisotropic diffusion of Mg to the c-axis has potential applications in the fabrication of unique vertical device structures such as super junctions.
Vertical GaN junction barrier Schottky (JBS) diodes with superior electrical characteristics and nondestructive breakdown were realized using selective-area p-type doping via Mg ion implantation and subsequent ultra-high-pressure annealing. Mg-ion implantation was performed into a 10 μm thick Si-doped GaN drift layer grown on a free-standing n-type GaN substrate. We fabricated the JBS diodes with different n-type GaN channel widths Ln = 1 and 1.5 μm. The JBS diodes, depending on Ln, exhibited on-resistance (RON) between 0.57 and 0.67 mΩ cm2, which is a record low value for vertical GaN Schottky barrier diodes (SBDs) and high breakdown (BV) between 660 and 675 V (84.4% of the ideal parallel plane BV). The obtained low RON of JBS diodes can be well explained in terms of the RON model, which includes n-type GaN channel resistance, spreading current effect, and substrate resistance. The reverse leakage current in JBS diodes was relatively low 103–104 times lower than in GaN SBDs. In addition, the JBS diode with lower Ln exhibited the leakage current significantly smaller (up to reverse bias 300 V) than in the JBS diode with large Ln, which was explained in terms of the reduced electric field near the Schottky interface. Furthermore, the JBS diodes showed a very high current density of 5.5 kA/cm2, a low turn-on voltage of 0.74 V, and no destruction against the rapid increase in the reverse current approximately by two orders of magnitude. This work demonstrated that GaN JBS diodes can be strong candidates for low loss power switching applications.
Herein, we propose and demonstrate the edge termination for GaN-based one-sided abrupt p–n junctions. The structure is comprised of a combination of a shallow negative bevel mesa and selective-area p-type doping under the mesa. Based on the Technology Computer Aided Design (TCAD) simulation, the maximum electric field at the junction edge is markedly reduced to approximately 1.3 times that of the parallel-plane electric field in the proposed structure, which is almost half of the unimplanted diode. The TCAD simulation also shows that the shallow mesa angle of effectively reduces the optimum acceptor concentration (Na) in the implanted region and enhances the breakdown voltage. The optimum Na value can be covered by the proposed technology based on the Mg-ion implantation and subsequent ultra-high-pressure annealing (UHPA). Using the formation of the shallow bevel mesa, the Mg-ion implantation, and the UHPA process, we experimentally demonstrate the p–n diodes with a breakdown voltage over 600 V, which is in good agreement with the TCAD simulation. The proposed method can be applied to a vertical trench-gate metal-oxide-semiconductor field-effect transistor with a high figure-of-merit.
We investigated the excitation intensity ( ) dependent photoluminescence (PL), at room temperature (RT), from GaN-based metal-insulator-semiconductor structures under gate bias (VG) from accumulation to deep depletion resulting in variations of the space charge region width. We found that depending on VG, different -dependencies of the YL band energy position (blueshift or redshift), shape (band enlargement or narrowing) and intensity (signal saturation) can be obtained. In order to explain such an unusual YL behavior, we developed a phenomenological PL model, which is based on the solution of the three-dimensional Poisson's equation, current continuity equations and rate equations, and which takes into account the grain structure of GaN layers and the contribution of interface regions into recombination processes. Our model reproduced well the experimental -dependencies of the YL band intensity. It also predicts that YL arises from the donor-acceptor pair (DAP) recombination in very limited areas (width of several nanometers) inside the depletion regions related to grain/grain interfaces and external crystal surfaces. On this basis, we showed that VG-controlled -dependencies of the YL peak position and shape, can be well explained if we assume that YL is due to DAP-type transitions, in which the final state consists of the Coulomb interaction and strong interaction between the dipole moment of ionized DAP and the depletion region electric field. This recombination mechanism can play a significant role at RT, but should be negligible at low temperatures, where one can expect the significant reduction of interface barriers under illumination.
20 June 2025 in IEEE Transactions on Electron Devices
This study presents the fabrication of vertical GaN junction barrier Schottky (JBS) diodes by using magnesium (Mg) ion implantation on a channeling condition and subsequent ultrahigh-pressure annealing (UHPA). We performed a technology computer-aided design (TCAD) simulation study to confirm the effect of channeled implantation. In the JBS diode with deep Mg profile by channeled implantation, the electric field at the surface was suppressed more efficiently than that in the random (conventional) implantation JBS diodes. It leads to the reduction of leakage current owing to the thermionic-field emission (TFE) at the Schottky interface. As expected, channeled implantation JBS diodes showed low leakage current and high breakdown voltage (BV) depending on the n-GaN channel region width. This study demonstrated that channeled implantation of Mg ions can be an effective method for the fabrication of GaN JBS diodes.
22 July 2024 in IEEE Transactions on Electron Devices
This study investigates the influence of different magnesium (Mg) ion implantation techniques on the performance of gallium nitride (GaN)-based junction termination extension (JTE) structures. To this end, we perform a systematic TCAD simulation study on JTE structures using two different implantation techniques of Mg ions: 1) channeled implantation and 2) random (conventional) implantation. We perform channeled and random Mg ion implantations and subsequent activation annealing to GaN epitaxial layers to obtain actual Mg depth profiles experimentally. We used the obtained profiles for the TCAD simulations. The Mg-channeled implanted JTE structure exhibits a significantly larger optimal JTE dose window compared to the Mg-random implanted JTE structure. This is because, in the JTE structure with a channeled Mg depth profile, the electric field crowding is more suppressed than in the JTE structure with a random Mg depth profile. These results indicate that deep-graded Mg depth profiles are more suitable for the relaxation of electric field strength concentrations than shallower profiles. In addition, we found that the Mg-channeling-based JTE structure was more advantageous than the Mg-random-based JTE structure that considers the interface charge at the passivation SiO2/GaN interface.