Objective: The aim of this in vitro study was to evaluate the accuracy of shade matching using two spectrophotometric devices. Materials and Methods: Thirteen patients who require a full coverage restoration for one of their maxillary central incisors were selected while the adjacent central incisor was intact. 3 same frameworks were constructed for each tooth using computer-aided design and computer-aided manufacturing technology. Shade matching was performed using Vita Easyshade spectrophotometer, Shadepilot spectrophotometer, and Vitapan classical shade guide for the first, second, and third crown subsequently. After application, firing, and glazing of the porcelain, the color was evaluated and scored by five inspectors. Results: Both spectrophotometric systems showed significantly better results than visual method (P < 0.05) while there were no significant differences between Vita Easyshade and Shadepilot spectrophotometers (P < 0.05). Conclusion: Spectrophotometers are a good substitute for visual color selection methods.
1 April 2014 in Journal of Oral and Maxillofacial Surgery
Purpose: Denture base materials are commonly exposed to different denture cleansers which can affect their essential properties. This study aimed to assess the effect of denture cleansers on color stability and surface roughness of poly methyl methacrylate (PMMA) denture bases fabricated from different techniques: Conventional heat‐polymerizing, CAD/CAM additive and CAD/CAM subtractive.Materials and Methods: In this in vitro study, 24 disc‐shaped specimens were fabricated by the mentioned methods for each group. The initial color and surface roughness of specimens were recorded. The specimens were randomly divided into three subgroups (n = 8): a control subgroup (distilled water), and two experimental subgroups of bioactive oxygen tablet (Corega) and 1% sodium hypochlorite solution. Then they were immersed in the solutions simulating 180 days of clinical use. Color change (∆E) was measured by a spectrophotometer according to the CIE L*a*b* color space and the American National Bureau of Standards (NBS = 0.92 × ∆E). Final surface roughness was recorded by a profilometer and its change was calculated. The Kruskal–Wallis test followed by the Wilcoxon signed rank test were used for statistical analyses (α = .05).Results: The conventional and CAD/CAM subtractive groups showed an increase in surface roughness following immersion in hypochlorite solution (p < .05). After immersion in the solutions, the highest surface roughness was noted in the conventional group, and the lowest in the CAD/CAM additive group. The CAD/CAM additive group experienced a significant color change in hypochlorite solution (p < .05) and showed the highest color change while the CAD/CAM subtractive group showed the lowest color change in all denture cleanser solutions.Conclusion: Although the CAD/CAM additive denture base resins had the lowest surface roughness after exposure to denture cleanser solutions, they showed significant color change, which should be taken into account. Using hypochlorite as a denture cleanser should be cautioned due to its negative effects on the surface roughness and color stability of denture base materials.
This study aimed to evaluate the influence of different shades and brands of resin-based luting agents on the final color of a leucite-reinforced veneering ceramic. This in-vitro study was done on 36 ceramic discs (IPS Empress I, 11 × 0.5 mm, A2 shade) and 36 cement disks (11 × 0.2 mm) made of Panavia SA Cement Plus (Kuraray Medical Inc.) and Choice2 (Bisco Inc., Schumburg) brands in translucent, universal A2, and opaque shades (n = 6 per each color in each resin cement brand). Color parameters (CIEL*a*b*) of ceramic specimens were calculated without and with each brand/shade of resin-based luting agents by using a spectrophotometer, and put into CIELab formula. The color differences (ΔE) between the two sets of measurements were calculated and analyzed with two-way ANOVA and Tukey's post hoc test (α = 0.05). Both the resin-based luting agent shade (P < 0.001) and brand (P = 0.023) significantly affected the color differences. ΔE values were significantly different between Panavia-opaque and Choice2-opaque (P < 0.001). No significant difference existed between ΔE of the two brands in A2 (P = 0.178) and translucent shades (P = 0.079). The ΔE values of Panavia-A2 was significantly different from the translucent and opaque shades of the same brand. Moreover, the ΔE of Choice2-translucent shade was significantly lower than that of A2 and opaque shades. The ΔE values were higher than the clinically-acceptable threshold in all groups (ΔE > 3.7) except for Choice2-translucent (ΔE = 3.37). The final color of leucite-reinforced veneering ceramic can be affected by the same shades of resin-based luting agents from different brands and different shades of resin-based luting agents from the same brand.
Although all-ceramic restorations are broadly used, there is a lack of information concerning how their fit is affected by fabrication procedure and marginal configuration. The purpose of this study was to evaluate the marginal fit of zirconia CAD/CAM ceramic crowns before and after porcelain firing. The influence of finish line configuration on the marginal fit was also evaluated. Twenty standardized zirconia CAD/CAM copings were fabricated for chamfer and shoulder finish line designs (n=10). The marginal fit of specimens was measured on 18 points, marked on the master metal die by using a digital microscope. After the crowns were finalized by porcelain veneering, the measurements of marginal fit were performed again. The means and standard deviations were calculated and data were analyzed using student’s t-test and paired t-test (α=0.05). There were significant differences between marginal fit of chamfer and shoulder finish line groups before and after porcelain firing (p= 0.014 and p= 0.000, respectively). The marginal gap of copings with shoulder finish line was significantly smaller than those with chamfer configuration (p= 0.000), but there were no significant differences between the two marginal designs, after porcelain firing (p= 0.341). Porcelain veneering was found to have a statistically significant influence on the marginal fit of zirconia CAD/CAM crowns. Both margin configurations showed marginal gaps that were within a reported clinically acceptable range of marginal discrepancy.
27 July 2024 in Journal of Maxillofacial and Oral Surgery