Ship collisions are rare events that may have a significant impact on the safety of people, ships, and other marine structures, as well as on the environment. Because of this, they are extensively studied but events that just precede collision are often overlooked. To rationally assess collision risks and consequences, a ship’s trajectory, and consequently the velocity and collision angle, should be known. One way to achieve this is through accurate modelling of ship manoeuvrability in collision analysis using non-linear FEM (NFEM). The Abkowitz manoeuvring model is implemented in the LS-Dyna software code and is therefore coupled with FEM calculations. Hydrodynamic forces are calculated in each time step of the LS-Dyna calculation and added to the FE model continuously through calculation. The accuracy of the calculations depends on the choice of and values of hydrodynamic derivatives from the Abkowitz model. Abkowitz’s model derives hydrodynamic forces in the Taylor expansion series to provide hydrodynamic derivatives. The application of the procedure is sensitive on higher-order Taylor series members. This article reviews different sets of hydrodynamic derivatives available for the KVLCC2 ship. Each of them is incorporated into the LS-Dyna NFEM solver by a user-made Fortran subroutine, with standard Zigzag and turning manoeuvres simulated and results compared with the experimental tests. As a result, the optimal selection of hydrodynamic derivatives is determined, laying a foundation for assessing the risk of ship collision due to different ship manoeuvres prior to the collision itself.

In light of escalating global energy demands and the imperative to reduce greenhouse gas emissions, the efficient transportation of liquefied natural gas (LNG) has become increasingly critical. As the evaporation of LNG from storage tanks represents a significant energy loss, improving tank insulation is crucial to optimize storage efficiency. This paper conducts a structural assessment of a smaller-sized Type C independent tank made of AISI 304L steel and examines the impact of two insulation techniques—vacuum and perlite—on their heat, structural, and fatigue behavior. Utilizing the finite element method (FEM), this study performs a heat transfer analysis followed by a structural analysis under combined loads in accordance with the International Gas Carrier (IGC) code. The subsequent fatigue analysis follows IGC procedures and is performed using third-party software. This article presents a detailed analysis of the heat transfer throughout the entire LNG tank and the stress levels under various combined load scenarios while providing insights into the critical stress points and the areas with the lowest fatigue life. Finally, this study confirms the viability of using both novel materials, perlite as an insulation material and Durolight for the tank support, because they meet the required limits.

Wind-induced waves can lead to the partial or complete wash-over of beaches, causing erosion that impacts both the landscape and tourist infrastructure. In some regions of the world, e.g., Croatia, this process, which usually occurs during a harsh winter, has a major impact on the environment and the economy, and preventing or reducing this process is highly desirable. One of the simplest methods to reduce or prevent beach erosion is the use of innovative underwater structures designed to decrease wave energy by reducing wave height. In this study, submerged breakwaters are numerically investigated using various topologies, positions, and angles relative to the free surface. Not only is the optimal topology determined, but the most efficient arrangement of multiple breakwaters is also determined. The advantage of newly developed submerged breakwaters over traditional ones (rock-fixed piers) is that they do not require complex construction, massive foundations, or high investment costs. Instead, they comprise simple floating bodies connected to the seabed by mooring lines. This design makes them not only cheap, adaptable, and easy to install but also environmentally friendly, as they have little impact on the seabed and the environment. To evaluate wave damping effectiveness, the incompressible computational fluid dynamics (ICFD) method is used, which enables the use of a turbulence model and the possibility of accurate wave modelling.

The remains of ancient ships from various time periods are commonly found on land and under the sea in conditions that make it difficult to reconstruct their original form and structure. For this reason, the reconstruction should be supported by other data, such as data on similar ships, but also by certain assumptions. The results of the reconstruction are significant not only in a historical sense but are of exceptional importance when building floating replicas. Two ships, Nin 1 and Nin 2, today for promotional purposes known as Condurae Croaticae, were found in Nin (Croatia) at the end of the 1960s. They are about 8 to 10 m long, and tentatively dated to the 11th century AD, although there are indications that they could be dated two centuries later. Based on archaeological finds exhibited in the Museum of Nin Antiquities, hull line drawings were created, according to which two floating replicas were made at the end of the 1990s. Considering the problem of hogging that appeared in both ships, a new proposal for the reconstruction of the original hull lines was performed based on the available documentation. The aim of this paper is a systematic analysis of its calm water resistance. Based on the established credibility of experimental testing, a scale model (1:4 ratio) of the Nin 1 vessel is constructed and evaluated through towing tank experiments. The second approach, the CFD method, is a reliable numerical method for calm resistance estimation, but it is rarely used in the analysis of ancient ships. Finally, the widely used empirical Holtrop method is also applied, but it was developed for ships of larger dimensions and with large parts of flat bottoms and, therefore, the more appropriate Delft Hull Yacht Series method is also tested. The results obtained by applying the four mentioned methods are compared and discussed.

Wooden ships on the shipwreck sites are usually only partially preserved, and reconstructing the original hull lines requires considerable effort. The shape of the hull has a direct effect on the ship’s capacity to carry cargo, as well as on its speed and stability. When reconstructing the hull lines, the incomplete nature of the archaeological remains results in the interpretation of the available data. The outcome, therefore, depends on the assumptions and decisions associated with the reconstruction process. This paper examines how the variation in a single parameter, namely, the beam, affects the performance of the vessel. Considering the availability of the model, the Kyrenia ship from the fourth/third century BC is used as a case study. The scope of this paper is to demonstrate and quantify the effect of beam variation on ancient ship performance, namely, the ship cargo capacity, stability, and resistance. Kyrenia ship was used as a study case based on hull lines proposed by Steffy in 1985. The aim is not to modify Steffy’s original reconstruction but to demonstrate that small deviations could significantly affect the performance of the vessel. In addition, an increase in the height of the ship’s sides is proposed as a possible solution to increase the load capacity of the ship. The opportunity to explore a whole set of trials and reconstructive variations with naval engineering software can deepen our understanding of ship performance, allowing us to improve our approach to reconstruction, too.

This study presents a finite element-based numerical simulation of a shipwreck scenario at the 4th-century BC underwater archaeological site near the island of Žirje, integrating engineering analysis with archaeological interpretation. The site is notable for the wide scattering of amphorae across the seafloor. A scaled model, based on the well-documented Kyrenia shipwreck, found off the coast of Cyprus, was developed to approximate the estimated parameters of the Žirje vessel, incorporating reduced dimensions, an adjusted freeboard, and a total deadweight of approximately six tons. The finite element model of the ship, its cargo, and the seabed was developed using LS-DYNA R11.1. software. Instead of fluid modelling, the study employed explicit dynamic analysis with a rigid seabed, gravitational loading, and automatic contact to reduce computational cost. A series of parametric simulations explored the effects of roll, yaw, and varying gravitational forces on the sinking behaviour and cargo dispersion. Results indicate that only certain non-uniform sinking conditions, combined with seabed currents, accurately replicate the archaeological distribution of the amphorae. This approach underscores the value of integrating finite element analysis (FEA) with archaeological data to generate digitally supported hypotheses, demonstrating how numerical reconstruction can enhance the interpretation of complex underwater archaeological sites.