In this study, the degradation of bisphenol A (BPA) by ozonation was studied systematically by investigating the effects of different factors, including ozone dosages (0.25–1.50 mg/L), temperatures (10–50°C), initial solution pH (3.0–11.0) and interfering ions. The reaction kinetics were analyzed at the same time. In addition, the generation of intermediates was analyzed and the possible mechanism was proposed by combining with the density functional theory (DFT) calculation. At last, the variation and controlling effect of toxicity was also evaluated. The results showed that ozonation had a stronger degrading ability of BPA (1.0 mg/L). A complete removal efficiency was obtained within 10 min when dosing only 1.0 mg/L ozone. The BPA degradation reactions were well fitted with pseudo-second-order kinetics and could well adapt with the wide range of pH (3.0–9.0), during which over 91% removal of BPA was achieved. The indirect pathway by •OH oxidation was proved mainly responsible for BPA degradation by the scavenging and electron paramagnetic resonance experiments. HCO3−, NH4+ and humic acid showed a certain inhibiting effect. Fe3+ and Cu2+ played a catalytic role on BPA degradation. The DFT calculation has identified that the active regions of BPA was focused at C6, C4, C5 and C1 in terms of radical and electrophilic attack. Thus, combining the results of DFT with GC/MS-MS detection, two degradation pathways of BPA were proposed. Toxicity evaluation showed that, due to the generation and accumulation of more toxic intermediates, values of T% had a sharp increase at initial stage. However, with ozone dosage increasing to 1.50 mg/L, the toxicity could be effectively controlled much lower (5%) than BPA itself (49%).
10 January 2023 in Frontiers in Environmental Science
UV/sulfite process without oxygen has been extensively explored and used for the degradation of many micro-pollutants. In the present work, a UV/sulfite process in the presence of oxygen was applied to degrade a widely used pharmaceutical compound, metformin (MET). The results showed that the oxygen-involved UV/sulfite process could efficiently degrade MET. At an initial concentration of 2.5 mg/L, 86.0% of MET was removed from the contaminated water within 180 min irradiation at a sulfite dosage of 10 mM, solution pH of 9, and UV intensity of 4,092 μW/cm2. In addition, sulfate radical (SO4•-), hydroxide radical (•OH), hydrogen atom (•H), and hydrated electron (eaq−) were found to be the dominant active species contributing to MET removal in the studied process through scavenging experiments. The increase in UV intensity, sulfite dosage, solution pH, and reaction temperature enhanced MET degradation in the investigated process to a certain extent, whereas the introduction of bicarbonate and fulvic acid slightly suppressed MET degradation. Finally, the degradation products of MET were identified. The oxygen-involved UV/sulfite process exhibited a remarkable denitrification capacity (>80%) in MET. The findings of this study may offer a novel approach for treating emerging contaminants.
Preparing carbon aerogel in an eco-friendly and inexpensive manner remains a significant challenge. The carbon aerogels derived from food waste (FWCAs) with a three-dimensional connected network structure are successfully synthesized using microwave radiation. The as-prepared FWCA-4 (The KOH/C ratio is 4) has a large specific surface area (1470 m2/g), pore volume (0.634 m3/g), and a high degree of graphitization. Band-like lattice stripes with a spacing of 0.34 nm, corresponding to the graphite plane, are observed. A high specific capacitance of 314 F/g at 1.0 A/g and an excellent capacitance retention (>90% after 10,000 cycles) make the FWCA-4 suitable for high-performance supercapacitor electrode materials. Furthermore, the specific surface area and pore volume of FWCA-4 are larger and the degree of graphitization is higher than in ordinary porous carbon derived from food waste (FWPC). The assembled symmetrical solid capacitor from FWCA-4 exhibits a maximum energy density of approximately 179.9 W/kg in neutral ion electrolytes. Thus, food waste is successfully used to prepare carbon aerogels through a gelation process using microwave radiation. The recycling of waste biomass is achieved, and the results provide insights for the preparation of carbon aerogels using biomass.
1 July 2025 in Ecotoxicology and Environmental Safety
Peroxyacetic acid (PAA), as a potential disinfectant, can be used to drive an ultraviolet-based advanced oxidation process (UV-AOP) for water purification. In this study, low-pressure ultraviolet (LP-UV) was innovatively coupled with PAA to construct an LP-UV/PAA system for the degradation of chloroquine phosphate (CQP), an antiviral drug that is widely present in the aqueous environment. The results showed that the system removed 99.89 % of CQP within 30 min, which was significantly better than single LP-UV or PAA treatment. The common natural substances in the actual water body, such as Cl-, Br- and HCO3-, etc., slightly promoted the degradation of CQP. The free radical quenching experiments confirmed that ·OH was the dominant active species in the CQP degradation process, and the secondary effects included CH3· and CH3COOO·. The system simultaneously demonstrated excellent sterilizing ability and disinfection by-product control, which indicated that it had the prospect of engineering application. This work not only deepens the theoretical understanding of the UV/PAA reaction pathway, but also provides an efficient and scalable technical solution for the treatment of CQP pollution in practical water treatment scenarios.