Ming Yeng Chan

Dr. Ming Yeng Chan

orcid

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 October 2022 in Polymer Engineering & Science
Verified
Journal Article
Closed access
JCJia Sheng Chu
Jia Sheng Chu
SKSeong Chun Koay
Seong Chun Koay
MCMing Yeng Chan
Ming Yeng Chan
HCHui Leng Choo
Hui Leng Choo
TOThai Kiat Ong
Thai Kiat Ong

11 October 2018 in Journal of Thermoplastic Composite Materials
Verified
Journal Article
Closed access
PDF file
KNKuhananthan Nanthakumar
Kuhananthan Nanthakumar
MCMing Yeng Chan
Ming Yeng Chan
KCKoay Seong Chun
Koay Seong Chun
This research covers the preparation of poly(lactic acid) (PLA)/sugarcane leaves fibre (SLF) biofilms via a solvent-casting method. The results showed that the tensile strength and Young’s modulus of PLA/SLF biofilms increased with the increasing of SLF content. Nevertheless, the elongation at break showed an opposite trend as compared to tensile strength and Young’s modulus of biofilms. Moreover, water absorption properties of PLA/SLF biofilms increased with the increasing of SLF content. In contrast, the tensile strength and Young’s modulus of biofilms were enhanced after bleaching treatment with hydrogen peroxide on SLF, but the elongation at break and water absorption properties of bleached biofilms were reduced due to the improvement of filler–matrix adhesion in biofilms. The tensile and water properties were further discussed using B-factor and Fick’s law, respectively. Furthermore, the functional groups of unbleached and bleached SLF were characterized by Fourier transform infrared analysis.

13 September 2018 in Journal of Thermoplastic Composite Materials
Verified
Journal Article
Closed access
PDF file
KCKoay Seong Chun
Koay Seong Chun
VSVarnesh Subramaniam
Varnesh Subramaniam
MCMing Yeng Chan
Ming Yeng Chan
PMPang Ming Meng
Pang Ming Meng
CRChantara Thevy Ratnam
Chantara Thevy Ratnam
KCKean How Cheah
Kean How Cheah
Ever since the development of lightweight polystyrene foam, the material has become an attractive single-use product packaging in various industries. Despite its high versatilities, post consumed polystyrene foam has very low rate of recycling due to the high cost during transportation and there is hardly any established economical recycling route. The purpose of this research is to investigate the potential of converting the polystyrene foam waste as raw material for producing wood plastic composite (WPC). In the present study, predefined formulation of recycled polystyrene (rPS), durian husk fiber (DHF) and processing aid Ultra-PlastTM WP516 were melt blended with the aid of Haake internal mixer. The homogenous mixtures were subsequently compression molded to form WPC. The effect of material compositions on tensile, thermal, and morphological properties of the rPS/DHF composite was highlighted. The results showed that tensile strength and modulus increase with fiber content, while elongation at break and thermal stability were decreased. With higher loading of Ultra-PlastTM WP516, both tensile and thermal properties decreased. This research found that WPC with optimum strength of 18.8 MPa can be produced from rPS having 60 parts per hundred resin (phr) of DHF and 0.5 phr of Ultra-PlastTM WP516, albeit the measured tensile strength is lower compared to commercial alternatives. The resulting WPC possess great potential in none high strength, structurally demanding application.

5 November 2019 in Polymer Engineering & Science
Verified
Journal Article
Closed access
PDF file
SLSing Li Ling
Sing Li Ling
SKSeong Chun Koay
Seong Chun Koay
MCMing Yeng Chan
Ming Yeng Chan
Kim Yeow TshaiKim Yeow Tshai
Kim Yeow Tshai
TCThevy Ratnam Chantara
Thevy Ratnam Chantara
MPMing Meng Pang
Ming Meng Pang

29 April 2018 in Journal of Thermoplastic Composite Materials
Verified
Journal Article
Open access
CPCh’nG Zhin Pao
Ch’nG Zhin Pao
MCMing Yeng Chan
Ming Yeng Chan
Recently, many agricultural waste were left for open burning or as landfill in many agricultural land, for example, coconut shells. Besides, expanded polystyrene (EPS) foam is one of the most used plastic products which mostly ends up in landfilling as many of its products were made for one-time use only. In order to reduce these wastes, this project focuses on the preparation of a new material that is coconut shell powder (CSP)-filled EPS wood plastic composite (WPC). This research investigates the effects of CSP content and alkaline treatment with sodium hydroxide (NaOH) on mechanical and water absorption properties of EPS/CSP WPCs. The mechanical properties, such as tensile strength, Young’s modulus and flexural modulus, increased as the CSP content increased. However, elongation at break and flexural strength decreased with CSP content. Moreover, water absorption of EPS/CSP WPCs showed an increasing trend with CSP content. After alkali treatment, the mechanical properties of EPS/CSP WPCs were enhanced, but the water absorption properties of treated EPS/CSP WPCs were reduced due to the reduction of the –OH groups of CSP. Fourier transform infrared analysis was carried out to measure the functional groups of untreated and treated CSP. The fracture surface of CSP, untreated and treated EPS/CSP WPCs were examined by scanning electron microscopy.

29 June 2021 in Journal of Natural Fibers
Verified
Journal Article
Closed access
JLJ. J. Ariel Leong
J. J. Ariel Leong
SKS. C. Koay
S. C. Koay
MCMing Yeng Chan
Ming Yeng Chan
HCH. L. Choo
H. L. Choo
Kim Yeow TshaiKim Yeow Tshai
Kim Yeow Tshai
TOT. K. Ong
T. K. Ong
This research aimed at developing composite filament for fuse deposition modeling (FDM) application was carried out by recycling post-used expanded polystyrene foam (EPS) as a binding matrix for natural fibers derived from corn husk (CH) waste. The recycled polystyrene (rPS) resin, CH fibers, and predefined amount of processing aid were primarily compounded using a Brabender® internal mixer to produce composite masterbatch feedstock. The composite masterbatch was further blended with measured amount of rPS resin, and the mixtures were extruded into composite filament containing different weight percentage (wt%) of CH fiber loading, ranging from 2.5 to 10 wt%. The 3D printability of the composite filament was assessed through observation on melt flow behavior and viscosity of the molten composite material subjected to typical FDM process conditions, where tensile dumbbell specimen was produced. Through repeated attempts carried out to FDM 3D-print the rPS/CH fiber filled composite filament, the result suggested that higher FDM extrusion percentage was required to produce quality part from composite filament with increase fiber content from 2.5 to 7.5 wt%. Composite filament with 10 wt% fiber loading failed to be printed due to premature thermal degradation and the slightly higher melt viscosity that tend to clog the printer nozzle.