Dan Claudiu Negrau

Dr. Dan Claudiu Negrau

University of Oradea, Oradea, Bihor, Romania
orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 August 2021 in MATEC Web of Conferences
Verified
Journal Article
Open access
PDF file
DNDan Claudiu Negrau
Dan Claudiu Negrau
GGGavril Grebenisan
Gavril Grebenisan
IGIon Cosmin Gherghea
Ion Cosmin Gherghea
DADaniel Anton
Daniel Anton
The paper presents a case study which the additive manufacturing technology is combined with finishing process by cutting operations (turning) for manufacturing a part. The part was manufactured through additive manufacturing, using a 3D printer and the and the finishing process is performed by a lathe, resulting in technological properties and the corresponding dimensional accuracy. The research paper also contains the analysis of the roughness and other properties of the material from which the final part will be made. The manufactured part will be used as a support for the blades of a fan during the assembly process, which emphasizes that a part obtained by additive manufacturing (3D printing) can replace a part obtained by casting or fabrication by total cutting. In conclusion, obtaining the manufactured part by combining the two manufacturing processes, the lead time and the production cost has been significantly reduced, while the quality of the obtained product also increased, obtaining a very good roughness.

1 August 2019 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
DNDan Claudiu Negrau
Dan Claudiu Negrau
GGGavril Grebenisan
Gavril Grebenisan
CGC Gherghea
C Gherghea
The deformation of an aluminum plate, called in this paper, a support plate, which is part of a bending plastic deformation device, is studied in this paper using the Finite Elements Method, respectively design points of the design by optimization using features such as Design of Experiments and Response Surfaces. The start of the analysis was determined by a functional requirement in the design and construction of a sophisticated bending device controlled by steel plates for the production of exhausts for cars. To optimize the project, it was necessary to analyze the behavior of the active material and components of the device. The analysis of material and piece behavior, in working conditions, has been developed by addressing the facilities offered by Ansys software. Following FEA analysis, optimizing the active components of the device has provided proven results in practice through the execution and operation of the device, according to the technology required by the product designer.

1 October 2019 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
DNDan Claudiu Negrau
Dan Claudiu Negrau
CIC I Indre
C I Indre
GGGavril Grebenisan
Gavril Grebenisan
This work contains the 3D design and finite element analysis of a manual device for assembly by bending the sheets around an exhaust muffler. As a result of the design of the device, the requested was executed by the information provided by the mechanical designer; only when the device of bending was put into operation, some faults appeared, namely that its parts during the operation has been elastically deformed. For the construction of the elastically yielding parts, the finite element method was used to study the behavior of the tool. Following the FEA analysis, it was concluded that the dimensions and material from which those pieces had been built had to be changed. By making the new parts based on FEA calculations, they no longer elastically yield (elastic deformation less than 0.1%), so the device is accepted by the customer.

1 August 2019 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
DNDan Claudiu Negrau
Dan Claudiu Negrau
GGGavril Grebenisan
Gavril Grebenisan
TVT Vesseleny
T Vesseleny
This paper presents the theoretical basis of the approach to Finite Element Analysis (FEA) techniques and their application in the case of a bending request for a piece of aluminum sheet. The plate of a bending device deforms elasto-plastically under the action of the drive forces of the device, but also under the action of the reaction forces in the supports, more for a material such as aluminum and a few times less for a structural steel. If the forces acting on the device deform the carrier plate, which is in the operator’s attention, in the elastic field, then there is no danger of permanent deformations occurring. Conversely, if deformation exceeds the threshold of elastic deformation, the material undergoes plastic deformation stresses, then the piece deforms plastic, with the risk of permanent deformations occurring. These deformations, in the first place, can generate production errors, or device failure, by modifying the execution rates and the games in the studied ensemble. This is precisely the purpose of this work: to prove, with the results of the FEA, that in the case of a certain material, with the same configuration of working conditions, the system can function without producing errors, obtaining qualitatively conformable parts.

20 September 2023 in Preprints.org
Verified
Preprint
Open access
PDF file
DNDan Claudiu Negrau
Dan Claudiu Negrau
PRPancu Rares
Pancu Rares
GGGavril Grebenisan
Gavril Grebenisan
This paper presents an original method of additive manufacturing of cylindrical parts with variable circumference thickness, which allows the control of the deposition of molten material using an algorithm for decomposing the part geometry into volumetric elements with known dimensional configuration. In the absence of a post-processor capable of controlling additive manufacturing on a 5-axis numerical control machine, control of the deposition of molten material is done using parameterized programs, which can control both the feed speeds of the machine tool axes and the specific functions of the printing equipment. Additive manufacturing can make a positive contribution to sustainable development compared to traditional manufacturing technologies, thus making a positive contribution for a sustainable future. The aim of the work is to make it possible to 3D print parts with variable wall thickness using a CNC machining centre. To obtain the variable thickness layer we have implemented an original method of deposition with molten material (FDM), the coordination of the system composed of physical elements respectively programmable elements, is realized through control functions materialized in parameterized part programs, the generated outputs being the variable speed of the machine axes on a circular trajectory, the angular positioning, the filament advance.

1 January 2019 in ANNALS OF THE ORADEA UNIVERSITY. Fascicle of Management and Technological Engineering.
Verified
Journal Article
Closed access
DNDan Claudiu Negrau
Dan Claudiu Negrau
GGG Grebenişan
G Grebenişan
TVT Vesselenyi
T Vesselenyi