Overhead conductor rail (OCR) is an important power supply device in tunnel railway lines. The penalty method is widely adopted to model the dynamic interaction behaviour of the pantograph-OCR system (POCRs), while it is difficult to determine a proper contact stiffness value. This paper proposes a three-dimensional contact formulation for the POCRs based on the Lagrange multiplier method. Accurate contact forces can be obtained easily by this contact formulation without the trouble of determining the contact stiffness. Contact force is defined in the global coordinate system as a three-dimensional vector. Coulomb law of friction is adopted in this paper to describe the tangential contact force, and the train speed is included in the contact formulation. The central finite difference approximation method is utilised, and an iteration procedure is elaborated to calculate the accurate contact force vector. The proposed contact formulation is verified by comparing simulation results with in-line measured data. The maximum statistical relative error of the contact force is only 2.63%. The advantages of the proposed contact formulation are also demonstrated by comparing it with the penalty method.
22 December 2023 in IEEE Transactions on Transportation Electrification
Overhead Conductor Rail (OCR) is a power supply device in tunnel railways. This paper aims to investigate the influence of train speed and support stiffness on the pantograph-OCR system (POCRs) dynamic behaviour, and propose improvement measures to the existing power feeding system to accommodate higher speeds. Firstly, a field test is conducted to measure the equivalent stiffness of the supports currently utilised in the OCR system. The test results are adopted to modify the OCR model. Subsequently, a lumped mass model of the pantograph and the OCR model considering interlocking joints are developed. The analysis reveals that the contact force exhibits a nonlinear variation as the support stiffness increases, and good dynamic interaction can be achieved when support stiffness falls between 10 4 and 10 5 N/m. Then time-frequency analysis explains the origin and amplification factors of multiple frequency components of the contact forces. The results show that structural wavelengths such as span length, half span length and interlocking joint interval are the primary sources of contact force components. Finally, the resonance mechanism of the POCRs is revealed, explaining the occurrence of deteriorated interaction performance under specific support stiffness.
13 December 2021 in IEEE Transactions on Instrumentation and Measurement
Overhead conductor rail (OCR) is widely used in tunnel railway lines to provide continuous energy for electric trains. Current studies mainly focus on the interaction of the low-speed pantograph–OCR system (POCRs), whereas the increase in speed poses new challenges in the power supply of the locomotives. This article develops a mathematical model based on the absolute nodal coordinate formulation for simulating the dynamic behavior of POCRs that operates at high speed, integrated with the contact wire irregularities (CWIs). The presented model is verified by comparing it with the measured data, and the maximum statistical relative error of the contact force is only 7.52%. Next, the sensitivity analysis is performed to reveal the effect of critical parameters of the OCR on the contact force at 200 km/h. Furthermore, the resonance mechanism of the POCRs is revealed based on a simplified model, which can be used to explain the appearance of bad current collection quality with some specific span lengths and CWI wavelengths. Finally, a linearized simulation algorithm is presented, saving about 99.65% of the computation time. The comparative analysis indicates that the geometrical nonlinearity of OCR can be neglected for improving computational efficiency.
The rigid catenary system is widely used in tunnels to power electric trains via contact with a pantograph. Due to gravity, the contact wire normally has a sag that may affect the dynamic interaction performance with a pantograph. To reduce the contact wire sag, the most efficient measure is to improve the moment of inertia of the conductor rail, which is used to clamp the contact wire. Six new types of conductor rail with large moments of inertia are developed based on a conventional conductor rail. Then both the static and dynamic analyses are conducted to investigate the performance of the new types of conductor rail with a big moment of inertia. The conductor rail’s 3D solid finite element model is built using a finite element approach. The vertical deflection and the stress distribution are comparatively analyzed among different types of conductor rail. The analysis results indicate that the vertical deflection and maximum stress are significantly reduced when using the conductor rail with a large moment of inertia. The best performance is observed when the conductor rail of case 1 is used. The maximum sag is reduced by 28.37%, and the maximum stress is decreased by 27.76% compared with the conventional conductor. Finally, a pantograph model is included to evaluate the dynamic performance of the conductor rail with large moments of inertia. The results indicate that contact force fluctuation is significantly reduced after the conductor rails with large moments of inertia are presented. The conductor rail of case 1 shows the best performance, which can reduce the contact force standard deviation by 32% and 27% at speeds of 160 km/h and 200 km/h.
30 September 2024 in IEEE Transactions on Instrumentation and Measurement
In high-speed railways, the pantograph serves as the sole apparatus for collecting electric energy, directly impacting the operational safety of high-speed trains through its structural stability. As train speed increases, the interaction between the pantograph and the catenary becomes more pronounced, potentially compromising the structural safety of the pantograph during operation. Previous studies have not fully accounted for the significant effects of large fluctuations in the high-speed pantograph-catenary contact force on the pantograph structure. This paper addresses the issue by establishing a comprehensive finite element model of the pantograph that incorporates parametric structural dimensions. The validation of the model is confirmed through lumped mass parameter identification and modal analysis tests. Additionally, a dynamic coupling model of the pantograph-catenary system is developed to assess the load impact on the pantograph. By applying the load, the dynamic deformation and stress of the pantograph are analyzed to identify critical structural locations during high-speed operation. The findings reveal that the structural strength of the pantograph at 400 km/h falls below the permissible threshold. Consequently, a neural network-based optimization approach is proposed to minimize the maximum stress and deformation of the pantograph at this speed. The pantograph’s structural performance response surface is constructed using sensitivity analysis and a radial basis neural network. Finally, a multi-objective genetic algorithm (MOGA) is employed to search the response surface and achieve optimal results.