A novel backdrivable 3-[R(RR-RRR)SR] kinematically redundant (6+3)-degree-of-freedom (DOF) spatial hybrid parallel robot with revolute actuators is proposed for low-impedance physical human–robot interaction. The kinematic model is developed based on the constraint conditions of the robot. It is shown that the type II (parallel) singularities can be completely avoided, thereby yielding a very large translational and orientational workspace. A workspace analysis is presented in order to demonstrate the capabilities of the robot. Mechanisms are then introduced to use the redundant DOF of the robot to operate a gripper with the robot actuators, which are mounted on or close to the base, thus reducing the inertia of the moving parts. The architecture of the robot makes it possible to use direct drive motors, thereby making the robot easily backdrivable and allowing the use of a very simple and effective controller. A prototype of the robot is then designed and built and the large workspace of the robot as well as the effortless physical human–robot interaction are demonstrated. The controller of the robot is then described, including a position control mode and a control mode for physical interaction, which does not require the use of a force/torque sensor or joint torque sensors. Because of its backdrivability and low moving inertia, the robot is particularly well-suited for physical human–robot interaction, as demonstrated in the accompanying videos.
This paper presents an indoor localization system to determine the position of a target in 3D environment using RF and Ultrasound. Distances from the target to reference nodes are calculated using Time Difference of Arrival (TDoA) principle. Then trilateration algorithms, namely Linear Least Squares, Nonlinear Least Squares, Closed-Form Position and Cayley-Menger Determinants, are applied to determine the target position. All software programs, except the one on pre-processing board, are developed based on QNX Neutrino RTOS which has many advantages such as micro-kernel architecture, POSIX-certified. QNX is also applied popularly in modern embedded systems. A hardware system is built and experiments have been carried out to verify the system operation and compare the accuracy between the positioning algorithms.
This paper presents an improved indoor localization system based on radio frequency (RF) and ultrasonic signals, which we named the SNSH system. This system is composed of a transmitter mounted in a mobile target and a series of receiver nodes that are managed by a coordinator. By measuring the Time Delay of Arrival (TDoA) of RF and ultrasonic signals from the transmitter, the distance from the target to each receiver node is calculated and sent to the coordinator through the CAN network, then all the information is gathered in a PC to estimate the 3D position of the target. A sine wave detector and dynamic threshold filter are applied to provide excellent accuracy in measuring the range from the TDoA results before multilateration algorithms are realized to optimize the accuracy of coordinate determination. Specifically, Linear Least Square (LLS) and Nonlinear Least Square (NLS) techniques are implemented to contrast their performances in target coordinate estimation. RF signal encoding/decoding time, time delay in CAN network and math calculation time are carefully considered to ensure optimal system performance and prepare for field application. Experiments show that the sine wave detector algorithm has greatly improved the accuracy of range measurement, with a mean error of 2.2 mm and maximum error of 6.7 mm for distances below 5 m. In addition, 3D position accuracy is greatly enhanced by multilateration methods, with the mean error in position remaining under 15 mm. Furthermore, there are 90% confidence error values of 23 mm for LLS and 20 mm for NLS. The update in the overall system has been verified in real system operations, with a maximum rate of 25 ms, which is a better result than many other existing studies.
1 February 2024 in IEEE/ASME Transactions on Mechatronics
This article proposes a novel grasping control method for a kinematically redundant parallel (KRP) robot with a remotely operated gripper. The proposed method consists of a motion controller and a force controller acting on each leg of the robot. The motion control model applies the computed torque method, and the force control model is based on the forces applied by each leg to the platform. These forces are decomposed into two main components: The first component generates the grasping forces, while the second one balances the platform. Since the different force components are calculated independently, the grasping forces are not coupled with others. As a result, the grasping forces can be precisely controlled without using any force/torque sensor. The grasping process introduces actuation redundancy and changes the topology of the KRP robot. In such a situation, there are infinitely many solutions for the forces in the robot, and three approaches are proposed to resolve the overconstraint. Once the forces applied on each leg are obtained, the actuated torques can be calculated based on the static force model of the leg. Finally, experiments are conducted on a prototype to verify the performance of the proposed control method.
1 May 2023 in IEEE/ASME Transactions on Mechatronics
In this article, we investigate the characteristics of a collaborative hybrid parallel robot. A comparison between this robot and other collaborative robots regarding the Cartesian inertia is presented to highlight the very low inertia of the hybrid parallel robot. A task space stiffness-damping control is also proposed. In order to improve the performance of macro--mini systems in the interaction context, an active macro-active mini system consisting of the hybrid parallel robot mounted on a three degrees of freedom (3-DOF) gantry translational robot is introduced. A control strategy for physical human–robot interaction is applied to the macro--mini arrangement. The stability of this method is analyzed and it is shown that the macro–mini combination is more stable than the mini alone. An experimental validation is then carried out. The results obtained with the hybrid parallel robot show that the desired interaction force can be tracked at high speed and that prescribed impedance parameters can be precisely rendered to the human operator without using any additional sensor. Also, it is pointed out that the bandwidth of interaction of the hybrid parallel robot, as well as of the macro--mini system is much higher than that of other commercial collaborative robots. In addition, other tests are realized on the macro–mini system in order to verify the performance and to demonstrate potential applications. The macro–mini robot introduced in this work yields a very intuitive human–robot interaction, which makes it ideal for many applications in which direct physical teaching or assistance is needed.