Upscaling of biomass pretreatment from laboratory scale to a bench-scale reactor is one of the important steps in the application of the pretreatment for pilot or commercial scale. This study reports the optimization of pretreatment conditions, namely reaction temperature and time, by one factor at a time (OFAT) method for the enhancement of enzymatic saccharification of oil palm empty fruit bunch (OPEFB). OPEFB was pretreated using high temperature-pressure steam reactor with different reaction temperatures (160, 170, 180, 190, 200 °C) and times (10, 20, 30, 40, 50 min). The effectiveness of the pretreatment was determined based on chemical compositions of raw OPEFB and OPEFB pulp and sugar production from enzymatic saccharification of the OPEFB pulp. Solubilized components from OPEFB, such as glucose, xylose, formic acid, acetic acid, 5-hydroxymethyl furfural (HMF), and furfural in the hydrolysate that generated during steam pretreatment were also determined. Pretreatment at 180°C for 20 min provides the highest sugar yields (97.30% of glucose yield per initial cellulose and 88.86% of xylose yield per initial hemicellulose). At the optimum condition, 34.9% of lignin and 30.75% of hemicellulose are successfully removed from the OPEFB and resulted in 3.43 delignification selectivity. The relationship between severity factor and by-products generated and the sugars obtained after enzymatic saccharification are discussed. The pulp of OPEFB at the optimum condition was also characterized for its morphological characteristic by scanning electron microscopy (SEM) and crystallinity by X-ray diffractometry (XRD). These pulp characteristics are then compared with those of the raw OPEFB. The steam pretreatment causes some fiber disruptions with more defined and opened structures and increases the crystallinity index (CrI) by 2.9% compared to the raw OPEFB.
The pseudostem of banana (Musa sp.) has a high value for fiber. In this study, we characterized two wild Musa acuminata, i.e., ssp. malaccensis (LIPI-030) (M1) and var. breviformis (LIPI-218) (M3), an accession of diploid M. acuminata cultivar “Pisang Rejang” (LIPI-048) (M2) and one accession M. balbisiana “Pisang Klutuk” (LIPI-054) (M4) for its chemical (including Syringyl (S) and Guaiacyl (G) ratio) physical and mechanical properties, fiber analysis, morphological analysis, functional groups, crystallinity, and thermal analysis. As a result, there are variations in chemical, physical, and mechanical properties, fiber length and diameter, crystallinity, and thermal analysis behavior for each banana species. “Pisang Klutuk” showed the most different characteristics compared to others. The cellulose content of all banana fibers has a close correlation with their tensile strength. Based on the fiber properties evaluation, var. breviformis (M3) has a tensile strength of 459.99 MPa, cellulose content of 33.30%, degree of crystallinity of 45.23%, degree of polymerization of 1199.15, and S/G ratio of 0.39 that suggested the most potential banana for fiber with high strength. The lignin S/G ratio of banana samples (M1-M2) showed a positive correlation with the degree of crystallinity and tensile strength, while it had a negative one with tensile modulus and strain. This study presented the importance of the S/G ratio and fiber properties that may aid the future application of Indonesian fiber in biomass conversion strategies.
Activated carbon was prepared from OPEFB by one step steam activation method. The adsorption performance for the removal of acid orange 52 (AO 52), reactive blue 19 (RB 19), basic violet 1 (BV 1) was investigated. Each dye has a different chemical structure such as azoic, anthraquinone, triarylmethane for AO 52, RB 19, and BV 1 respectively. The effects of adsorbent dosage, pH, and contact time on the adsorption process were studied. Experimental data were analyzed by model equations such as Langmuir, Freundlich and Temkin isotherms and it was found that the Langmuir isotherm model best fitted for all three dyes with R2 values is higher than 0.95. Langmuir model assumes a homogeneous nature and monolayer coverage of dye molecules at the outer surface of activated carbon. Adsorption kinetics was determined using pseudo-first-order, pseudo-second-order rate equations, Elovich model and also intraparticle diffusion models. Kinetic studies showed that the pseudo-second-order kinetic model better described the adsorption process with R2 values exceeds 0,99 compared with the other kinetics model. The SEM images showed AC pores was well developed with steam activation while wider porosity is created in the macropore range. FT-IR analysis had shown that the AC functional groups were disappeared because of vaporization the volatile materials when the heating process.Keywords:Activated Carbon, Adsorption Isotherms, Kinetic, OPEFB, Steam Activation