A novel aerobic moderately thermophilic bacterium, strain 3753O^T, was isolated from a Chukotka hot spring (Arctic, Russia) using the newly developed technology of laser engineering of microbial systems. Сells were regular short rods, 0.4×0.8–2.0 µm in size, with a monoderm-type envelope and a single flagellum. The temperature and pH ranges for growth were 42–60 °C and pH 6.5–8.5, the optima being 50–54 °C and pH 7.3. Strain 3753O^T grew chemoorganoheterotrophically on a number of carbohydrates or peptidic substrates and volatile fatty acids, and chemolithoautotrophically with siderite (FeCO₃) as the electron donor. The major cellular fatty acid was branched C_19 : 0. Phosphatidylethanolamine, phosphatidylglycerol and two unidentified phospholipids as well as two yellow carotenoid-type pigments were detected in the polar lipid extract. Strain 3753O^T was inhibited by chloramphenicol, polymyxin B, vancomycin, streptomycin, neomycin and kanamycin, but resistant to the action of novobiocin and ampicillin. The DNA G+C content was 69.9 mol%. The 16S rRNA gene as well as 51 conservative protein sequence-based phylogenetic analyses placed strain 3753O^T within the previously uncultivated lineage OLB14 in the phylum Chloroflexi . Taking into account the phylogenetic position as well as phenotypic properties of the novel isolate, the novel genus and species Tepidiforma bonchosmolovskayae gen. nov., sp. nov., within the Tepidiformaceae fam. nov., the Tepidiformales ord. nov. and the Tepidiformia classis nov. are proposed. The type strain of Tepidiforma bonchosmolovskayae is 3753O^T (=VKM B-3389^T=KTCT 72284^T).

Standard microorganism isolating technology applied for complex multiphase environmental samples such as soil or sediment needs pre-treatment steps to remove living cells from their mixed-phase microniche, by creating a liquid-phase sample. This process removes synergetic relationships, which help to maintain viability of yet-to-be-cultured and hard-to-culture bacteria. In this paper we demonstrate a high throughput Laser Micro-Sampling (LMS) technology for direct isolation of pure microbial cultures and microbial consortia from soil. This technology is based on laser printing of soil microparticles by focusing near-infrared laser pulses on specially prepared samples of a soil/gel mixture spread onto a gold-coated glass plate. Microsamples of soil are printed on glucose-peptone-yeast agar plates, to estimate the LMS process influence on functional and taxonomic microbial diversity, and on «Eco-log» sole carbon sources microplates, to investigate functional diversity by “metabolic fingerprinting”. The obtained results are compared with traditionally treated soil samples. It was shown that LMS treatment leads to increasing of cultured biodiversity and modifies the functional diversity. The strain of rare genus Nonomuraea was isolated by LMS from complex natural environment without using media selective for this genus.

A technology of laser engineering of microbial systems (LEMS) based on the method of laser-induced transfer of heterogeneous mixtures containing microorganisms (laser bioprinting) is described. This technology involves laser printing of soil microparticles by focusing near-infrared laser pulses on a specially prepared gel/soil mixture spread onto a gold-coated glass plate. The optimal range of laser energies from the point of view of the formation of stable jets and droplets with minimal negative impact on living systems of giant accelerations, laser pulse irradiation, and Au nanoparticles was found. Microsamples of soil were printed on glucose-peptone-yeast agar plates to estimate the LEMS process influence on structural and morphological microbial diversity. The obtained results were compared with traditionally treated soil samples. It was shown that LEMS technology allows significantly increasing the biodiversity of printed organisms and is effective for isolating rare or unculturable microorganisms.

Laser-induced forward transfer (LIFT) is a useful technique for bioprinting using gel-embedded cells. However, little is known about the stresses experienced by cells during LIFT. This paper theoretically and experimentally explores the levels of laser pulse irradiation and pulsed heating experienced by yeast cells during LIFT. It has been found that only 5% of the cells in the gel layer adjacent to the absorbing Ti film should be significantly heated for fractions of microseconds, which was confirmed by the fact that a corresponding population of cells died during LIFT. This was accompanied by the near-complete dimming of intracellular green fluorescent protein, also observed in response to heat shock. It is shown that microorganisms in the gel layer experience laser irradiation with an energy density of ~0.1–6 J/cm². This level of irradiation had no effect on yeast on its own. We conclude that in a wide range of laser fluences, bioprinting kills only a minority of the cell population. Importantly, we detected a previously unobserved change in membrane permeability in viable cells. Our data provide a wider perspective on the effects of LIFT-based bioprinting on living organisms and might provide new uses for the procedure based on its effects on cell permeability.

Laser bioprinting is a promising method for applications in biotechnology, tissue engineering, and regenerative medicine. It is based on a microdroplet transfer from a donor slide induced by laser pulse heating of a thin metal absorption film covered with a layer of hydrogel containing living cells (bioink). Due to the presence of the metal absorption layer, some debris in the form of metal nanoparticles is printed together with bioink microdroplets. In this article, experimental investigations of the amount of metal nanoparticles formed during the laser bioprinting process and transported in bioink microdroplets are performed. As metal absorption layers, Ti films with the thickness in the range of 25–400 nm, produced by magnetron spattering, were applied. Dependences of the volume of bioink microdroplets and the amount of Ti nanoparticles within them on the laser pulse fluence were obtained. It has been experimentally found that practically all nanoparticles remain in the hydrogel layer on the donor slide during bioprinting, with only a small fraction of them transferred within the microdroplet (0.5% to 2.5%). These results are very important for applications of laser bioprinting since the transferred metal nanoparticles can potentially affect living systems. The good news is that the amount of such nanoparticles is very low to produce any negative effect on the printed cells.

Laser bioprinting with gel microdroplets that contain living cells is a promising method for use in microbiology, biotechnology, and medicine. Laser engineering of microbial systems (LEMS) technology by laser-induced forward transfer (LIFT) is highly effective in isolating difficult-to-cultivate and uncultured microorganisms, which are essential for modern bioscience. In LEMS the transfer of a microdroplet of a gel substrate containing living cell occurs due to the rapid heating under the tight focusing of a nanosecond infrared laser pulse onto thin metal film with the substrate layer. During laser transfer, living organisms are affected by temperature and pressure jumps, high dynamic loads, and several others. The study of these factors’ role is important both for improving laser printing technology itself and from a purely theoretical point of view in relation to understanding the mechanisms of LEMS action. This article presents the results of an experimental study of bubbles, gel jets, and shock waves arising in liquid media during nanosecond laser heating of a Ti film obtained using time-resolving shadow microscopy. Estimates of the pressure jumps experienced by microorganisms in the process of laser transfer are performed: in the operating range of laser energies for bioprinting LEMS technology, pressure jumps near the absorbing film of the donor plate is about 30 MPa. The efficiency of laser pulse energy conversion to mechanical post-effects is about 10%. The estimates obtained are of great importance for microbiology, biotechnology, and medicine, particularly for improving the technologies related to laser bioprinting and the laser engineering of microbial systems.