Stochastic ray tracing is used for rendering photorealistic images formed by augmented reality optical systems that combine the image generated by an optoelectronic device with the image of...
Virtual sensing technology uses mathematical calculations instead of natural measurements when the latter are too difficult or expensive. Nowadays, application of virtual light sensing technology becomes almost mandatory for daylight analysis at the stage of architectural project development. Daylight Autonomy metrics should be calculated multiple times during the project. A properly designed building can reduce the necessity of artificial lighting, thus saving energy. There are two main daylight performance metrics: Spatial Daylight Autonomy (sDA) and Annual Sunlight Exposure (ASE). To obtain their values, we have to simulate global illumination for every hour of the year. A light simulation method should therefore be as efficient as possible for processing complex building models. In this paper we present a method for fast calculation of Daylight Autonomy metrics, allowing them to be calculated within a reasonable timescale. We compared our method with straightforward calculations and other existing solutions. This comparison demonstrates good agreement; this proves sufficient accuracy and higher efficiency of the method. Our method also contains an original algorithm for the automatic setting of the sensing area. The sDA metric is calculated considering blinds control, which should open or close them depending on overexposure to direct sunlight. Thus, we developed an optimization procedure to determine the blinds configuration at any time.
This paper proposes using the Monte Carlo method to design optical systems with an indeterminate ray path. The main algorithms for direct stochastic ray tracing and programmed implementation of the given algorithms are considered. The work is illustrated with examples in which the scattered light is calculated in lens-based optical systems.
Nowadays the daylight analysis is widely used by architects because it influences on the room usage and comfortability. The natural daylight has a lot of benefits. There are many issues related to the daylight which affects the function and perception of the illuminated area. The issues are direct sunlight and discomfort glare, illumination level and distribution on the working plane. The correct building design that takes into account the daylight analysis aspects leads to decrease of the artificial light usage and energy saving. So simulation of the metrics used in daylight analysis is an important task. The paper considers the simulation of two main standard characteristics widely used in the modern daylight estimation: spatial Daylight Autonomy (sDA) and Annual Sunlight Exposure (ASE). The calculation of both metrics is regulated by the Illuminating Engineering Society (IES) standards. The metric calculation provides daylight illumination data for whole year with one hour step. This means that several thousand simulations have to be run. So effective light simulation methods must be elaborated and used here. The paper presents the methods which deal with rather complex and precise building models under daylight illumination and realistic environment. Spatial Daylight Autonomy metric is calculated considering blinds control that opens or closes them depending on the over-exposure by the direct sunlight. Thus, simulation of sDA involves an optimization procedure defining blinds configuration at each hourly moment. The sDA and ASE calculations for architecture scene are provided as examples.
The work is devoted to the development of a new method for reconstructing the scattering properties of a rough surface, which is described using the bi-directional scattering distribution function (BSDF). There are several different methods of BSDF reconstruction using various approaches. However, they all have their drawbacks: for example, a method based on modeling the measured distribution of heights often requires a complicated fit apart from the expensive measurements themselves, various analytical methods are usu-ally operable within the average roughness values with their standard distribution, and a rather good and universal method for optimizing the normals distribution density does not support internal reflections on the elements of the roughest surface. The proposed solution uses the geometry models of the rough surface, which allows simulating a physically more accurate propagation of light through the rough surface taking into account internal reflections, and hence a more accurate reconstruction of the bidirectional scattering distribution function. The results of BSDF reconstruction with the new method are proved by comparison with measurement results.
The work is devoted to the investigation of the best and reasonable methods to reconstruct the scattering properties of inks and paints widely used in modern electronic devices containing various light guiding plates and fibers. Typically scattering properties for inks have a volume scattering nature however it can be complicated with surface scattering because of the microroughness of ink layers. Both the volume and surface scattering reconstruction are considered in the given paper. Typically scattering properties of inks are described with bidirectional scattering functions (BSDF) and the BSDF is required from the internal side of the material of light-guiding elements. It cannot be measured directly because neither detector of the measuring device nor the light source cannot be placed inside the material. The only way to solve the problem of BSDF extraction for such cases is to build computer models of volume and surface scattering for inks and then with optimization procedures reconstruct parameters for these models which can provide surface scattering close enough to scattering of real samples of inks and paints. Light propagation in ink media is very complex requiring a long calculation time. As a result, the selection of an effective optimization procedure is the key point of the task. Several more typical real samples with printed inks are selected for investigation. The achieved results of BSDF extraction show very good agreement with data obtaining by real measurement. The comparison is based on numerical comparison of light scattering of ink samples as well as its visual appearance.