The continuous monitoring of hydrogen sulfide (H2S) in exhaled breath enables the detection of health issues such as halitosis and gastrointestinal problems. However, H2S sensors with high selectivity and parts per billion-level detection capability, which are essential for breath analysis, and facile fabrication processes for their integration with other devices are lacking. In this study, we demonstrated Au nanosheet H2S sensors with high selectivity, ppb-level detection capability, and high uniformity by optimizing their fabrication processes: (1) insertion of titanium nitride (TiN) as an adhesion layer to prevent Au agglomeration on the oxide substrate and (2) N2 annealing to improve nanosheet crystallinity. The fabricated Au nanosheets successfully detected H2S at concentrations as low as 5.6 ppb, and the estimated limit of detection was 0.5 ppb, which is superior to that of the human nose (8-13 ppb). In addition, the sensors detected H2S in the exhaled breath of simulated patients at concentrations as low as 175 ppb while showing high selectivity against interfering molecules, such as H2, alcohols, and humidity. Since Au nanosheets with uniform sensor characteristics enable easy device integration, the proposed sensor will be useful for facile health checkups based on breath analysis upon its integration into mobile devices.
30 October 2019 in IEEE Transactions on Electron Devices
H₂ and NH₃ detection with low power consumption was demonstrated by integrated chemiresistive Pt and PtRh nanosheet sensors on glass substrates. The self-heating effects realized low power and local heating of metal nanosheet sensors, enabling the integration of sensors with different operating temperatures. Based on different resistance changes in Pt and PtRh nanosheets toward H₂ and NH₃, the concentration of each gas was detected from a gas mixture by consuming around 1-mW power. For decreasing the power consumption and further integration of sensors, sensor scaling and pulsed operations were numerically and experimentally studied. In addition to good connectivity of metal nanosheet sensors to large-scale integration (LSI) circuits, improvements of the power consumption by sensor scaling were proven. The pulsed operations required for integrated sensor arrays maintained a sensor response, or a resistance change, of approximately 60%, even when the power consumption was reduced by 20%.
Deformation potential (D ac ), which is one of the most important parameters determining the rate of electron-acoustic phonon scattering, in Si around MOS interfaces is thoroughly studied with regard to the dependences on surface carrier densities, back-gate biases, and device structures. It is demonstrated that D ac increases sharply at the MOS interface. To investigate the impact of the increased D ac on μ e , thick body-channel SOI MOSFETs, where drain current flows in the entire SOI layers, was fabricated. The carrier transport experiments reveal that μ e of greater than 1100 cm 2 V -1 s -1 is obtained in body-channel SOI MOSFETs with the SOI thickness of greater than 70 nm. By taking into account the Dac profile around the MOS interface, experimental μ e of SOI MOSFETs is numerically reproduced over a wide range of SOI thicknesses. μ e of the body-channel SOI MOSFETs is also well reproduced using the same D ac profile. Thus, it is concluded that D ac increases sharply at the Si/SiO 2 interface. The accurate modeling of the increased D ac around the Si/SiO 2 interface is indispensable for designing high-performance and/or low-power 3-D MOSFETs including FinFETs, extremely thin SOI MOSFETs, and nanowire MOSFETs, because these types of MOSFETs have greater interface-to-volume ratios.
HfO2 ferroelectricity is promising due to CMOS compatibility and various exceptional properties compared to conventional ferroelectricity. However, the mechanism for stabilizing the ferroelectric phase is still controversial. In this study, it is found that the redox reaction at high temperature strongly influences the phase transformation kinetics during the cooling process of Ge-doped HfO2 and alters the ferroelectric phase ratio at room temperature. The transformation to the non-ferroelectric phase becomes so fast during cooling in the oxidized sample that the transformation is unavoidable even in fast cooling and deteriorates ferroelectricity. It is further revealed that while the high-temperature redox reaction itself is reversible, the transformation to the non-ferroelectric phase during cooling is an irreversible process, which dominates ferroelectricity. These results help understand ferroelectric phase formation in doped HfO2 and elaborate the fabrication process of advanced ferroelectric devices.
9 January 2023 in Applied Catalysis B: Environment and Energy