Additive manufacturing (AM) of Ni-based super alloys is more challenging, compared to the production other metallic alloys. This is due to their high melting point and excellent high temperature resistance. In the present work, an Inconel 718 alloy was fabricated by a powder laser bed fusion (P-LBF) process and investigated to assess its microstructural evolution, together with mechanical properties. Additionally, the alloy was compared against the cast (and forged) alloy of similar composition. The microstructure of the P-LBF-processed alloy shows hierarchy microstructure that consists of cellular sub-structure (~100–600 nm), together with melt pool and grain boundaries, in contrast of the twin infested larger grain microstructure of the cast alloy. However, the effect of such unique microstructure on mechanical properties of the L-PBF alloy was overwritten, due to the absence of precipitates. The hardness of the L-PBF-processed alloy (330–349 MPa) was lower than that of cast alloy (408 MPa). The similar trend was also observed in other mechanical properties, such as Young’s modulus, resistance to plasticity and shear stress.

The deformation aspects associated with the micro-mechanical properties of the powder laser bed fusion (P-LBF) additively manufactured stainless steel 316L were investigated in the present work. Toward that, micro-pillars were fabricated on different planes of the stainless steel 316L specimen with respect to build direction, and an in situ compression was carried out inside the chamber of the scanning electron microscope (SEM). The results were compared against the compositionally similar stainless steel 316L, which was fabricated by a conventional method, that is, casting. The post-deformed micro-pillars on the both materials were examined by electron microscopy. The P-LBF processed steel exhibits equiaxed as well as elongated grains of different orientation with the characteristics of the melt-pool type arrangements. In contrast, the cast alloy shows typical circular-type grains in the presence of micro-twins. The yield stress and ultimate compressive stress of P-LBF fabricated steel were about 431.02 ± 15.51 − 474.44 ± 23.49 MPa and 547.78 ± 29.58 − 682.59 ± 21.59 MPa, respectively. Whereas for the cast alloy, it was about 322.38 ± 19.78 MPa and 477.11 ± 25.31 MPa, respectively. Thus, the outcome of this study signifies that the AM-processed samples possess higher mechanical properties than conventionally processed alloy of similar composition. Irrespective of the processing method, both specimens exhibit ductile-type deformation, which is typical for metallic alloys.

Metallic biomaterials in a solid form cause stress-shielding in orthopedic applications. Such implants also suffer from limited tissue attachment to become a part of the living system. In view of that, hydroxyapatite (HA) coating reinforced with titanium oxide (TiO₂) was deposited in a beta (β)-Titanium (Ti-35Nb-7Ta-5Zr) substrate by plasma spray. This allows us to exploit the best of the two materials, namely the relatively low modulus of β-Ti, together with the porous and bone-like structure/composition of the HA to facilitate cell growth. This is foreseen to be used as an implant, particularly for musculoskeletal-related disability. Detailed scanning electron microscopy (SEM) investigation shows the lamellar structure of the coating that is composed of different phases and some porosities. Transmission electron microscopy (TEM) confirms the co-existence of both the amorphous and crystalline phases that build up the coating structure. In situ micro-mechanical tests revealed that the HA-TiO₂ coating was low in strength and modules compared to that of the substrate material, together with lower ductility. The yield stress and modulus of elasticity of the coating were about 877 ± 174 MPa and 447 ± 24 MPa, respectively. In contrast, the beta (β)-Ti substrate possesses about 990 ± 85 MPa of yield stress and 259 ± 19 MPa modulus of elasticity. The deformation mechanism was also quite different, where the coating crumbled under compressive loading, featuring limited ductility with cleavage (brittle)-type fracture, and the substrate showed plastic flow of materials in the form of slip/shear planes with extended ductility.

In this study, Zn-reinforced Mg matrix composite materials were produced via powder metallurgy by exposing them to ball milling at varying mechanical milling times. Following ball milling, the powders were cold-pressed under 600 MPa to obtain green compacts. The sintering process was carried out in a tube furnace under an argon atmosphere at 500 °C for 120 min. The effects of different milling times (2 h, 4 h, and 8 h) on particle and grain size, as well as the influence of sintering temperature and time on the microstructure, were investigated through SEM analysis. Phase evolution and changes in crystal planes occurring after ball milling were revealed by XRD analysis. SEM images show that Zn particles were homogeneously distributed within the matrix after 8 h of milling. Furthermore, it can be clearly stated that the highest hardness values were obtained from the samples produced after 8 h of milling. The sample group with the highest density, least mass loss, and lowest degradation rate was obtained from materials produced from 4 h ball milled powders. The intermetallic phase formed in the powder structure after 8 h of milling tends to reduce density and corrosion properties. The findings reveal that the addition of these alloys to pure Mg clearly enhances its hardness and density, while also imparting superior corrosion resistance. These combined improvements suggest that the developed materials hold strong potential for application in biomedical and clinical environments, where both mechanical strength and corrosion resistance are critical.

This study investigates solid-state diffusion bonding between two INCONEL 617 alloy samples using field-assisted sintering technology (FAST). The study focuses on analyzing the faying surface validating the theoretical alloy design modeling done by the CALculation of PHAse Diagrams (CALPHAD) approach followed by experimental validation. Varying kinetics’ limitations enabled phase stability and phase control governed by the CALPHAD approach alloy design. The alloy design contains a pseudo-binary phase diagram assisted with thermal mapping of a property phase diagram to obtain the optimum temperature of solid-state diffusion bonding while understanding phase fields and their evolution through Molybdenum (Mo) increasing content and temperature increase. The FAST parameters recommended by CALPHAD were 800 °C under 10 MPa pressure with a holding time of 30 min. The investigation observations were promising in a way that the faying surface contains gamma (γ) only, while the further region on the alloy contains γ and gamma prime (γ′). It is worth mentioning that FAST joining resulted in fine faying surface thickness of around 10 μm and a controlled heat affected zone (HAZ) leading to relevant reduction in the recrystallization zone yielding an average grain size of 60–100 μm before and after diffusion bonding. Furthermore, two modes of metal carbide (MC) have been found; MC formed under the faying surface and micro-MC pools formed around the faying surface.