The article deals with the investigation of geopolymer foams (GFs) synthesized using by-products coming from the (i) screening-, (iv) pyrolysis-, (iii) dust abatement- and (iv) fusion-processes of the secondary aluminum industry. Based on principles of the circular economy to produce new technological materials, the experimental study involves industrial by-products management through the recovery, chemical neutralization, and incorporation of these relatively hazardous waste into the GFs. The geopolymeric matrix, consisting of metakaolin (MK) and silica sand (SA) with a 1:1 wt.% ratio, and chopped carbon fibers (CFs, 1 wt.% MK), was doped with the addition of different aluminum-rich industrial by-products with a percentage from 1 to 10 wt.% MK. The gas (mainly hydrogen) produced during the chemical neutralization of the by-products represents the foaming agents trapped in the geopolymeric structure. Several experimental tests were carried out to characterize the mechanical (flexural, compressive, and Charpy impact strengths) and thermal properties (thermal conductivity, and diffusivity, and specific heat) of the GFs. Results identify GFs with good mechanical and thermal insulation properties, encouraging future researchers to find the best combination (for types and proportions) of the different by-products of the secondary aluminum industry to produce lightweight geopolymer foams. The reuse of these industrial by-products, which according to European Regulations cannot be disposed of in the landfill, also brings together environmental sustainability and safe management of hazardous material in workplaces addressed to the development of new materials.
Construction and demolition waste (CDW) from earthquake rubbles was used here as recycled aggregates (RA) in cementitious binders. The materials were sorted in six groups: concrete (CO), natural stone (NS), tile (TI), brick (BR), perforated brick (PF) and roof tile (RT). The abundance (wt.%) of crystalline phases in each RA type was determined by X-ray Powder Diffraction (XRPD). Each group of RAs was used alone (100 wt.% of RA) and mixed with quartz-rich virgin aggregates (VA) to prepare 13 types of mortars (12 specimens per type): one reference mortar (RM) with only VA, six recycled aggregate mortars (RAM) and six recycled-plus-virgin aggregate mortars (RVAM). The physical and mechanical properties of aggregates and mortars reflect the type and abundance of crystalline phases in each CDW group. Recycled mortars rich in concrete, natural stones and tiles have better mechanical performance than mortars prepared with recycled bricks, perforated bricks and roof tiles. For each RA, RVAMs have superior mechanical characteristics than the corresponding RAM. Since the type and amount of phases contained in recycled aggregates strongly control the mechanical performance of new construction materials, they should be routinely quantified as reported here, in addition to other physical features (water absorption, density, etc.). The separation of heterogeneous CDW into homogeneous RA groups is necessary for the production of new construction materials with stable and predictable performances to ensure CDW recycling, especially in areas hit by major adverse events, where large amounts of still valuable materials could be used for reconstruction processes.
The O K-edge spectra of perovskites XTiO3 with X = Ca, Sr and Ba have been measured using electron energy-loss spectroscopy (EELS) and are analyzed using the ab initio full multiple-scattering (MS) calculations. The near-edge structures arise mainly from covalency by direct and/or indirect interaction between oxygen and metal. The coordination number of the cation and the site symmetry also influence the spectral shape and structures. Comparison of full MS simulations of different clusters around the excited atom allows to interpret and correlate the features present in the spectra of each compound to its specific atomic arrangement and electronic structure.
Construction and Demolition Waste (CDW) originating from the rubble produced by the 2016 seismic events in the Marche Region (Central Italy) has been studied, focusing on its mineralogical and chemical characteristics, to investigate its recycling potentials as a component for eco-sustainable building material or in the glass industry. The aim was to obtain a full characterization of the behaviour of this material at high T in order to determine the most advantageous conditions for vitrification, considered as an effective process for volume reduction as well as for immobilization of potentially hazardous elements. Vitrification experiments, carried out with thermal treatments as function of temperature/duration/particle size and aimed at amorphization, were carried out under atmospheric conditions, at different temperatures (1000-1250°C) and durations (2-8 hours). The study demonstrated that mineralogical composition remains homogeneous for grainsize <4 mm, thus suggesting that no sieving is necessary for recycling of the fine fractions, which are the most difficult to treat. Vitrification, although not achieved for the CDW sample up to 1250°C, due to high-Ca and low-Si contents, demonstrated that this CDW can produce an interesting refractory material and a porous/insulating material. However, experiments showed that full vitrification can be easily achieved by mixing urban waste glass and CDW, suggesting applications in the glass industry. Based on the chemical and mineralogical features of the products, other significant upgrading alternatives of recycling the CDW in different fields of applications are highlighted.