Senad Iseni

Mr. Senad Iseni


Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 December 2018 in CEAS Aeronautical Journal
Verified
Journal Article
Closed access
PDF file
SISenad Iseni
Senad Iseni
DMD. Micallef
D. Micallef
DEDavid Engelmann
David Engelmann
RMR. Mailach
R. Mailach
ENE. Nicke
E. Nicke
FMF. di Mare
F. di Mare

13 June 2016
Verified
Conference Paper
Closed access
PDF file
SISenad Iseni
Senad Iseni
DMDerek Micallef
Derek Micallef
RMRonald Mailach
Ronald Mailach
The fundamental mechanisms of blade flutter in modern aircraft engines are very complex. Flutter is a self-excited aeroelastic instability phenomenon which can finally cause material fatigue and, in the worst case, leads to blade failure within a very short time. The risk of flutter has to be considered during the design process and it is necessary to avoid that safety risk. The aeroelastic stability has to be ensured over the whole operating range especially near operating limits or typical flutter boundaries, like at stall or choke conditions. Topic of this paper are inlet distortions, which can have an additional influence on the flutter stability of the fan and the first compressor stages of jet engines. For this purpose a sinusoidal steady total pressure inlet distortion was defined. The influence of this inlet distortion on the flow field and the flutter stability of a highly loaded transonic fan rotor (NASA rotor 67) is investigated. The static deflection of the manufactured blade was considered using an accurate mesh morphing algorithm to update the fan performance characteristic considering the deformed blade structure. The fan rotor interacts with the upstream distorted flow which leads to different blade loading between the adjacent blades. A decoupled flutter stability analysis using the three-dimensional viscous flow solver TBLOCK and the open-source software package CalculiX for pre-stressed modal analyses is carried out. The flutter stability analyses with TBLOCK are performed using the so-called energy method which was introduced by Carta. In order to predict the flutter stability under clean inflow conditions, two different formulations, the Influence Coefficient Method (ICM) and Traveling Wave Mode (TWM) formulation, are taken into account, whereas both formulations are compared to each other. The influence coefficients were directly calculated from the TWM formulation to determine the required number of passages for the ICM. It can be seen that the stability curves obtained with the ICM are in a good agreement to the TWM-method. The use of ICM reduces substantially the number of unsteady CFD calculations because of the fact that only one unsteady CFD calculation is needed to reconstruct the stability curve for each eigenmode and operating point. The effect of inlet distortion on flutter stability is investigated applying the TWM formulation only. Indeed, it was established that such flow disturbances have also for specific blades, considering the operating point, eigenmode and nodal diameter a destabilising impact on their aeroelastic behavior and can cause flutter, which is mostly determined by the time-averaged stability parameter. Just in the same manner a positive effect was observed for certain blades in the blade row.

11 June 2018
Verified
Conference Paper
Closed access
PDF file
MKMatthias Kniefs
Matthias Kniefs
MLMartin Lange
Martin Lange
RMRonald Mailach
Ronald Mailach
SISenad Iseni
Senad Iseni
DMDerek Micallef
Derek Micallef
FMFrancesca di Mare
Francesca di Mare
Circumferential grooves in the casing of an axial compressor rotor or fan are known to be beneficial by extending the operating range of the machine. The goal of this paper is to analyze, if such grooves have a significant effect on the flutter stability, too. Generally, flutter should always be avoided as these self-excited blade vibrations can lead to high-cycle fatigue and therefore may damage the blades. In the present paper, the flutter behavior of a nominal fan is analyzed by performing a unidirectional Fluid-Structure-Interaction (FSI) simulation. To model the traveling wave arising during flutter, three different possibilities are available for computational fluid dynamics (CFD): the traveling wave mode method (TWM), the Fourier transformation method (FT) and the influence coefficient method (INFC). The TWM and INFC will be used within this investigation. At first, the computed flutter stability of the commercial CFD solver ANSYS CFX is compared to the results of the academic CFD solver TBLOCK. Therefore, a MATLAB code is introduced to be able to use the very efficient INFC method in combination with ANSYS CFX. The main part of this paper deals with the examination of three different circumferential grooves. Two of them had been optimized regarding aerodynamics and aeroacoustics in a joint research project and produce a minor change in flutter behavior. The third groove is of an arbitrary chosen design and it is discussed how its axial position has an impact on the vibration characteristic of the fan. All CFD simulations are conducted for two different operating points at 100% speed and the first two eigenmodes of the fan blade.

8 December 2016 in CEAS Aeronautical Journal
Verified
Journal Article
Closed access
PDF file
AAA.-L. Aulich
A.-L. Aulich
TST. Sauer
T. Sauer
SISenad Iseni
Senad Iseni
AMA. Moreau
A. Moreau
DPD. Peitsch
D. Peitsch
ENE. Nicke
E. Nicke