ELIAS LOPEZ ALBA

Dr. ELIAS LOPEZ ALBA


Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 March 2018 in Materials
Verified
Journal Article
Open access
PDF file
EAELIAS LOPEZ ALBA
ELIAS LOPEZ ALBA
Sebastian SchmeerSebastian Schmeer
Sebastian Schmeer
Francisco A. DíazFrancisco A. Díaz
Francisco A. Díaz
The study of natural fiber reinforcement composite structures has focused the attention of the automobile industry due to the new regulation in relation to the recyclability and the reusability of the materials preserving and/or improving the mechanical characteristics. The influence of different parameters on the material behavior of natural fiber reinforced plastic structures has been investigated, showing the potential for transport application in energy absorbing structures. Two different woven fabrics (twill and hopsack) made of flax fibers as well as a non-woven mat made of a mixture of hemp and kenaf fibers were employed as reinforcing materials. These reinforcing textiles were impregnated with both HD-PE (high-density polyethylen) and PLA (polylactic acid) matrix, using a continuous compression molding press. The impregnated semi-finished laminates (so-called organic sheets) were thermoformed in a second step to half-tubes that were assembled through vibration-welding process to cylindric crash absorbers. The specimens were loaded by compression to determine the specific energy absorption capacity. Quasi-static test results were compared to dynamic test data obtained on a catapult arrangement. The differences on the specific energies absorption (SEA) as a function of different parameters, such as the wall thickness, the weave material type, the reinforced textiles, and the matrix used, depending on the velocity rate application were quantified. In the case of quasi-static analysis it is observed a 20% increment in the SEA value when wove Hopsack fabric reinforcement is employed. No velocity rate influence from the material was observed on the SEA evaluation at higher speeds used to perform the experiments. The influence of the weave configuration (Hopsack) seems to be more stable against buckling effects at low loading rates with 10% higher SEA values. An increase of SEA level of up to 72% for PLA matrix was observed when compared with HD-PE matrix.

2 February 2018 in Materials
Verified
Journal Article
Open access
PDF file
ÁMÁngel Jesús Molina-Viedma
Ángel Jesús Molina-Viedma
EAELIAS LOPEZ ALBA
ELIAS LOPEZ ALBA
LFLuis Felipe-Sesé
Luis Felipe-Sesé
Francisco A. DíazFrancisco A. Díaz
Francisco A. Díaz
JRJavier Rodríguez-Ahlquist
Javier Rodríguez-Ahlquist
MIManuel Iglesias-Vallejo
Manuel Iglesias-Vallejo
In real aircraft structures the comfort and the occupational performance of crewmembers and passengers are affected by the presence of noise. In this sense, special attention is focused on mechanical and material design for isolation and vibration control. Experimental characterization and, in particular, experimental modal analysis, provides information for adequate cabin noise control. Traditional sensors employed in the aircraft industry for this purpose are invasive and provide a low spatial resolution. This paper presents a methodology for experimental modal characterization of a front fuselage full-scale demonstrator using high-speed 3D digital image correlation, which is non-invasive, ensuring that the structural response is unperturbed by the instrumentation mass. Specifically, full-field measurements on the passenger window area were conducted when the structure was excited using an electrodynamic shaker. The spectral analysis of the measured time-domain displacements made it possible to identify natural frequencies and full-field operational deflection shapes. Changes in the modal parameters due to cabin pressurization and the behavior of different local structural modifications were assessed using this methodology. The proposed full-field methodology allowed the characterization of relevant dynamic response patterns, complementing the capabilities provided by accelerometers.

25 February 2021 in Sensors
Verified
Journal Article
Open access
PDF file
ÁMÁngel Jesús Molina-Viedma
Ángel Jesús Molina-Viedma
EAELIAS LOPEZ ALBA
ELIAS LOPEZ ALBA
LFLuis Felipe-Sesé
Luis Felipe-Sesé
Francisco A. DíazFrancisco A. Díaz
Francisco A. Díaz
Experimental characterization and validation of skin components in aircraft entails multiple evaluations (structural, aerodynamic, acoustic, etc.) and expensive campaigns. They require different rigs and equipment to perform the necessary tests. Two of the main dynamic characterizations include the energy absorption under impact forcing and the identification of modal parameters through the vibration response under any broadband excitation, which also includes impacts. This work exploits the response of a stiffened aircraft composite panel submitted to a multi-impact excitation, which is intended for impact and energy absorption analysis. Based on the high stiffness of composite materials, the study worked under the assumption that the global response to the multi-impact excitation is linear with small strains, neglecting the nonlinear behavior produced by local damage generation. Then, modal identification could be performed. The vibration after the impact was measured by high-speed 3D digital image correlation and employed for full-field operational modal analysis. Multiple modes were characterized in a wide spectrum, exploiting the advantages of the full-field noninvasive techniques. These results described a consistent modal behavior of the panel along with good indicators of mode separation given by the auto modal assurance criterion (Auto-MAC). Hence, it illustrates the possibility of performing these dynamic characterizations in a single test, offering additional information while reducing time and investment during the validation of these structures.

23 September 2016 in Measurement Science and Technology
Verified
Journal Article
Closed access
PDF file
EAELIAS LOPEZ ALBA
ELIAS LOPEZ ALBA
LFL Felipe-Sesé
L Felipe-Sesé
SSS Schmeer
S Schmeer
FDF A Díaz
F A Díaz
In the current paper, an optical low-cost system for 3D displacement measurement based on a single camera and 3D digital image correlation is presented. The conventional 3D-DIC set-up based on a two-synchronized-cameras system is compared with a proposed pseudo-stereo portable system that employs a mirror system integrated in a device for a straightforward application achieving a novel handle and flexible device for its use in many scenarios. The proposed optical system splits the image by the camera into two stereo images of the object. In order to validate this new approach and quantify its uncertainty compared to traditional 3D-DIC systems, solid rigid in and out-of-plane displacements experiments have been performed and analyzed. The differences between both systems have been studied employing an image decomposition technique which performs a full image comparison. Therefore, results of all field of view are compared with those using a stereoscopy system and 3D-DIC, discussing the accurate results obtained with the proposed device not having influence any distortion or aberration produced by the mirrors. Finally, the adaptability of the proposed system and its accuracy has been tested performing quasi-static and dynamic experiments using a silicon specimen under high deformation. Results have been compared and validated with those obtained from a conventional stereoscopy system showing an excellent level of agreement.

5 February 2018 in Materials
Verified
Journal Article
Open access
PDF file
ÁMÁngel Jesús Molina-Viedma
Ángel Jesús Molina-Viedma
EAELIAS LOPEZ ALBA
ELIAS LOPEZ ALBA
LFLuis Felipe-Sesé
Luis Felipe-Sesé
Francisco A. DíazFrancisco A. Díaz
Francisco A. Díaz
The modal characterization of automotive lighting systems becomes difficult using sensors due to the light weight of the elements which compose the component as well as the intricate access to allocate them. In experimental modal analysis, high speed 3D digital image correlation (HS 3D-DIC) is attracting the attention since it provides full-field contactless measurements of 3D displacements as main advantage over other techniques. Different methodologies have been published that perform modal identification, i.e., natural frequencies, damping ratios, and mode shapes using the full-field information. In this work, experimental modal analysis has been performed in a multi-component automotive lighting system using HS 3D-DIC. Base motion excitation was applied to simulate operating conditions. A recently validated methodology has been employed for modal identification using transmissibility functions, i.e., the transfer functions from base motion tests. Results make it possible to identify local and global behavior of the different elements of injected polymeric and metallic materials.

17 September 2018 in Sensors
Verified
Journal Article
Open access
PDF file
LFLuis Felipe-Sesé
Luis Felipe-Sesé
ÁMÁngel Jesús Molina-Viedma
Ángel Jesús Molina-Viedma
EAELIAS LOPEZ ALBA
ELIAS LOPEZ ALBA
Francisco A. DíazFrancisco A. Díaz
Francisco A. Díaz
Three-dimensional digital image correlation (3D-DIC) has become the most popular full-field optical technique for measuring 3D shapes and displacements in experimental mechanics. The integration of fringe projection (FP) and two-dimensional digital image correlation (FP + DIC) has been recently established as an intelligent low-cost alternative to 3D-DIC, overcoming the drawbacks of a stereoscopic system. Its experimentation is based on the colour encoding of the characterized fringe and speckle patterns required for FP and DIC implementation, respectively. In the present work, innovations in experimentation using FP + DIC for more accurate results are presented. Specifically, they are based on the improvement of the colour pattern encoding. To achieve this, in this work, a multisensor camera and/or laser structural illumination were employed. Both alternatives are analysed and evaluated. Results show that improvements both in three-dimensional and in-plane displacement are obtained with the proposed alternatives. Nonetheless, multisensor high-speed cameras are uncommon, and laser structural illumination is established as an important improvement when low uncertainty is required for 2D-displacement measurement. Hence, the uncertainty has been demonstrated to be reduced by up to 50% compared with results obtained in previous experimental approaches of FP + DIC.