The growing need for materials that are eco-friendly and sustainable in the industrial sector has shifted focus from synthetic fossil to natural fibers, alongside the utilization of recycled polymer textiles. This research introduces a novel method for using end-of-life textiles, such as polyester and polyamide fabrics, in the production of composite materials, aiming to lessen textile waste and enhance material longevity. The mechanical attributes of flax fabric (FF), flax–recycled polyamide fabric (F/RPA), and flax–recycled polyester fabric (F/RPES) composite laminates are assessed through tensile, flexural, interlaminar shear, and Charpy impact tests. The study revealed that the addition of end-of-life synthetic fibers improves tensile strength, while the trend in modulus values suggests that flax provides a high degree of stiffness to the composites, which is moderated by the addition of synthetic fibers. This effect is consistent across both tensile and flexural testing, although the impact on stiffness is more significant in bending. The inclusion of polyester fibers in the composite laminate resulted in significant enhancements, with an 11.1% increase in interlaminar shear maximum force, a 17.4% improvement in interlaminar shear strength, and a 67.1% rise in un-notch impact energy, compared to composites made with only flax fiber (FF). The microscopic examination uncovered the internal structure and demonstrated a clear, strong bond between the polyester and polyamide fiber layers with the flax fibers. Additionally, the life cycle assessment revealed that the F/RPES composite had less environmental impact than FF and F/RPA in all 18 categories analyzed. This indicates that the environmental footprint of producing F/RPES is smaller than that of both FF and F/RPA.
The rising industrial demand for environmentally friendly and sustainable materials has shifted the attention from synthetic to natural fibers. Natural fibers provide advantages like affordability, lightweight nature, and renewability. Jute fibers’ substantial production potential and cost-efficiency have propelled current research in this field. In this study, the mechanical behavior (tensile, flexural, and interlaminar shear properties) of plasma-treated jute composite laminates and the flexural behavior of jute fabric-reinforced sandwich composites were investigated. Non-woven mat fiber (MFC), jute fiber (JFC), dried jute fiber (DJFC), and plasma-treated jute fiber (TJFC) composite laminates, as well as sandwich composites consisting of jute fabric bio-based unsaturated polyester (UPE) composite as facing material and polyethylene terephthalate (PET70 and PET100) and polyvinyl chloride (PVC) as core materials were fabricated to compare their functional properties. Plasma treatment of jute composite laminate had a positive effect on some of the mechanical properties, which led to an improvement in Young’s modulus (7.17 GPa) and tensile strength (53.61 MPa) of 14% and 8.5%, respectively, as well as, in flexural strength (93.71 MPa) and flexural modulus (5.20 GPa) of 24% and 35%, respectively, compared to those of JFC. In addition, the results demonstrated that the flexural properties of jute sandwich composites can be significantly enhanced by incorporating PET100 foams as core materials.
Catalytic combustion of hydrocarbons is an important technology to produce energy. Compared to conventional flame combustion, the catalyst enables this process to operate at lower temperatures; hence, reducing the energy required for efficient combustion. The reaction and activation energies of direct combustion of hydrocarbons (CH → C + H) on a series of metal surfaces were investigated using density functional theory (DFT). The data obtained for the Ag, Au, Al, Cu, Rh, Pt, and Pd surfaces were used to investigate the validity of the Brønsted-Evans-Polanyi (BEP) and transition state scaling (TSS) relations for this reaction on these surfaces. These relations were found to be valid (R2 = 0.94 for the BEP correlation and R2 = 1.0 for the TSS correlation) and were therefore used to estimate the energetics of the combustion reaction on Ni, Co, and Fe surfaces. It was found that the estimated transition state and activation energies (ETS = −69.70 eV and Ea = 1.20 eV for Ni, ETS = −87.93 eV and Ea = 1.08 eV for Co and ETS = −92.45 eV and Ea = 0.83 eV for Fe) are in agreement with those obtained by DFT calculations (ETS = −69.98 eV and Ea = 1.23 eV for Ni, ETS = −87.88 eV and Ea = 1.08 eV for Co and ETS = −92.57 eV and Ea = 0.79 eV for Fe). Therefore, these relations can be used to predict energetics of this reaction on these surfaces without doing the time consuming transition state calculations. Also, the calculations show that the activation barrier for CH dissociation decreases in the order Ag ˃ Au ˃ Al ˃ Cu ˃ Pt ˃ Pd ˃ Ni > Co > Rh > Fe.
Synthesis and combustion of hydrocarbons on a series of metal surfaces (Ag, Au, Al, Cu, Rh, Pt and Pd) were investigated using density functional theory (DFT). The adsorption energies for all species involved in these reactions, as well as the reaction energies and activation barriers on these surfaces, were calculated using the same models and DFT methods. The results were used to test the validity of the Brønsted–Evans–Polanyi (BEP) and transition state scaling (TSS) relationships for these reactions on these metal surfaces. The BEP relationship appears to be a valid indicator for the synthesis reactions with R2 values of 0.83, 0.88 and 0.94 for CO dissociation, CO hydrogenation and formyl (CHO) dissociation to CH + O, respectively. In addition to CH splitting, which has been studied before, the BEP relationship also appears to be valid for the CH oxidation and CHO dissociation to CO + H combustion reactions with R2 values of 0.94, 0.89 and 0.88, respectively. Also, the TSS relationship is excellent with a R2 value of 1 for all synthesis and combustion reactions. The BEP and TSS relationships were subsequently used to estimate the energetics of the synthesis and combustion reactions on Ni, Co and Fe surfaces. The results reveal that the transition state energies estimated by the TSS relationships are in better agreement with data obtained from DFT calculations than the activation energies estimated by the BEP relationships. Therefore, the TSS relationship is preferred when predicting energetics of these reactions on these surfaces.