Oblique convergence between the Australian and Pacific plates in South Island, New Zealand, has resulted in crustal thickening and distributed deformation within both plates. We measure this thickening and image the deformation with seismic wide‐angle data along a 600 km long transect that spans the plate boundary. P wave arrival times from 34,000 rays are used to construct a two‐dimensional model for seismic velocity with depth. Crustal velocities average 6.1 and 6.2 (±0.23) km/s for the Australian and Pacific sides of the boundary, respectively. Upper mantle velocities average 8.1 (±0.25) km/s. Distributed deformation is indicated by the following observations: a reduction in upper crustal and midcrustal velocities by 4% west of the plate boundary, ascribed to flexural bending stresses; a velocity reduction of 8% immediately east of the Alpine fault, linked to high pore fluid pressures; 17 km of crustal thickening to form a 44(±1.4) km deep crustal root that is offset 10–20 km SE of the highest mountains; a velocity reversal below the midcrust in the eastern part of the crustal root, caused either by heating or an artifact from seismic anisotropy; strong thickening of a 7.0(±0.4) km/s fast lower crust within the crustal root; and a low‐velocity zone in the Australian upper mantle due to sampling the slow orientation of upper mantle anisotropy.
Widespread gas venting along the Cascadia margin is investigated from acoustic water column data and reveals a nonuniform regional distribution of over 1100 mapped acoustic flares. The highest number of flares occurs on the shelf, and the highest flare density is seen around the nutrition-rich outflow of the Juan de Fuca Strait. We determine ∼430 flow-rates at ∼340 individual flare locations along the margin with instantaneous in situ values ranging from ∼6 mL min−1to ∼18 L min−1. Applying a tidal-modulation model, a depth-dependent methane density, and extrapolating these results across the margin using two normalization techniques yields a combined average in situ flow-rate of ∼88 × 106 kg y−1. The average methane flux-rate for the Cascadia margin is thus estimated to ∼0.9 g y−1m−2. Combined uncertainties result in a range of these values between 4.5 and 1800% of the estimated mean values.
Since 2009, unprecedented comprehensive long‐term gas hydrate observations have become available from Ocean Networks Canada's NEPTUNE cabled ocean observatory at the northern Cascadia margin. Several experiments demonstrate the scientific importance of permanent power and Internet connectivity to the ocean floor as they have advanced the field of gas hydrate related research. One example is the cabled crawler Wally at Barkley Canyon, enabling live in situ exploration of the hydrate mounds and its associated benthic communities through the crawler's mobility and permanent accessibility throughout the year. Another example is a bubble‐imaging sonar at Clayoquot Slope, revealing the strong relationship between ebullition of natural gas and tidal pressure, without apparent correlation to earthquakes, storms, or temperature fluctuations, in year‐long continuous recordings. Finally, regular observatory maintenance cruises allow additional science sampling including echo‐sounder surveys to extend the observatory footprint. Long‐term trends in the data are not yet apparent but can also become evident from continuous measurements, as ocean observatories such as NEPTUNE are built for a 25‐year lifetime, and expansion of the observatory networks makes these findings comparable and testable.
Offshore basalts, most commonly found as oceanic crust formed at mid-ocean ridges, are estimated to offer an almost unlimited reservoir for CO2 sequestration and are regarded as one of the most durable locations for carbon sequestration since injected CO2 will mineralize, forming carbonate rock. As part of the Solid Carbon project, the potential of the Cascadia Basin, about 200 km off the west coast of Vancouver Island, Canada, is investigated as a site for geological CO2 sequestration. In anticipation of a demonstration proposed to take place, it is essential to assess the tendency of geologic faults in the area to slip in the presence of CO2 injection, potentially causing seismic events. To understand the viability of the reservoir, a quantitative risk assessment of the proposed site area was conducted. This involved a detailed characterization of the proposed injection site to understand baseline stress and pressure conditions and identify individual faults or fault zones with the potential to slip and thereby generate seismicity. The results indicate that fault slip potential is minimal (less than 1%) for a constant injection of up to ~2.5 MT/yr. This is in part due to the thickness of the basalt aquifer and its permeability. The results provide a reference for assessing the potential earthquake risk from CO2 injection in similar ocean basalt basins.
Deep-sea environmental datasets are ever-increasing in size and diversity, as technological advances lead monitoring studies towards long-term, high-frequency data acquisition protocols. This study presents examples of pre-analysis data treatment steps applied to the environmental time series collected by the Internet Operated Deep-sea Crawler “Wally” during a 7-year deployment (2009–2016) in the Barkley Canyon methane hydrates site, off Vancouver Island (BC, Canada). Pressure, temperature, electrical conductivity, flow, turbidity, and chlorophyll data were subjected to different standardizing, normalizing, and de-trending methods on a case-by-case basis, depending on the nature of the treated variable and the range and scale of the values provided by each of the different sensors. The final pressure, temperature, and electrical conductivity (transformed to practical salinity) datasets are ready for use. On the other hand, in the cases of flow, turbidity, and chlorophyll, further in-depth processing, in tandem with data describing the movement and position of the crawler, will be needed in order to filter out all possible effects of the latter. Our work evidences challenges and solutions in multiparametric data acquisition and quality control and ensures that a big step is taken so that the available environmental data meet high quality standards and facilitate the production of reliable scientific results.