Jingyong Zhang

Dr. Jingyong Zhang

orcid

Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 July 2019 in Journal of Applied Physics
Verified
Journal Article
Closed access
PDF file
QZQian Zhang
Qian Zhang
JZJingyong Zhang
Jingyong Zhang
NLNeng Li
Neng Li
WCWenjie Chen
Wenjie Chen
An equimolar high-entropy carbide, (TiZrHfNbTa)C, which is a face-centered-cubic-structured solid solution, was synthesized through spark plasma sintering at 1950 °C. Its electronic properties, thermodynamic stability, and mechanical properties were thoroughly investigated by well-defined density functional theory calculations. Our results show that the strong bonds of TM–C (TM = Ti, Zr, Hf, Nb, Ta) in (TiZrHfNbTa)C lead to excellent mechanical properties relative to those of TaC, the solid-solution template, and limited lattice distortion, making its electronic structure similar to those of the constituent carbides. Calculated Young’s modulus (495 GPa) matches the experimental measurement data (479 GPa) well. This work provides insight into high-entropy (TiZrHfNbTa)C on an electronic scale and paves the way for the design of novel high-entropy carbides.

1 February 2020 in AIP Advances
Verified
Journal Article
Open access
PDF file
DWDangqiang Wang
Dangqiang Wang
XWXinzhi Wang
Xinzhi Wang
CXChongjun Xu
Chongjun Xu
ZFZhengyi Fu
Zhengyi Fu
JZJingyong Zhang
Jingyong Zhang
Almost fully dense pure alumina could be prepared by fast firing (FF) at a high temperature (greater than 1689 °C) and a high heating rate (∼350 °C/s) with a whole sintering cycle in approximately 2 min without pressure. Dynamics of the ultrafast densification was explored by comparing the densifying characters of FF sintering and conventional sintering. Results show that overlapping of surface/grain boundary diffusion and lattice diffusion caused by the high heating rate, as well as rapid migration of nanoscale particles caused by the high heating rate and the sufficiently high sintering temperature, leads to the ultrafast densification, which differs from conventional time-cost material diffusion. The ultrafast densification dynamics is expected to be helpful for understanding or developing new fast sintering methods for ceramics.

28 November 2006 in Journal of Materials Science
Verified
Journal Article
Closed access
PDF file
WKWang Kun
Wang Kun
FZFu Zhengyi
Fu Zhengyi
WWWang Weimin
Wang Weimin
WYWang Yucheng
Wang Yucheng
JZJingyong Zhang
Jingyong Zhang
ZQZhang Qingjie
Zhang Qingjie

1 December 2008 in Materials Research Bulletin
Verified
Journal Article
Closed access
FMFancheng Meng
Fancheng Meng
ZFZhengyi Fu
Zhengyi Fu
JZJingyong Zhang
Jingyong Zhang
HWHao Wang
Hao Wang
WWWeimin Wang
Weimin Wang
QZQingjie Zhang
Qingjie Zhang

1 June 2014 in Journal of Advanced Ceramics
Verified
Journal Article
Open access
PDF file
JZJingyong Zhang
Jingyong Zhang
HZHai Zhan
Hai Zhan
ZFZhengyi Fu
Zhengyi Fu
RTRichard Todd
Richard Todd
The main subject of this work is an investigation of the effects of heating rate and current on the crystallisation of amorphous precursors in spark plasma sintering (SPS). For this, dry gel of Al2O3-SiO2 with a molar ratio of 1:1, was synthesized and sintered in-situ by SPS, and also by hot pressing (HP) for comparison. Phase analysis showed that the only crystalline product in both cases was mullite, whose Al2O3 content was lower in the SPS specimens. The microstructures showed a low volume fraction of large mullite fibers in the SPS specimens, whereas a high volume fraction of fine equiaxed grains was present in the HP specimen. The main difference in microstructure between HP and SPS specimens could be explained in terms of the higher heating rate of the SPS specimens. The size of the SPS die also affected the size and aspect ratio of the mullite fibers produced, which might have been due to either the different electrical current required or a difference in specimen temperature profile.

29 September 2018 in Materials
Verified
Journal Article
Open access
PDF file
JLJun Li
Jun Li
Lisheng LiuLisheng Liu
Lisheng Liu
SXShuang Xu
Shuang Xu
JZJingyong Zhang
Jingyong Zhang
YWYuanli Wu
Yuanli Wu
The effects of carbon content on the mechanical properties and deformation mechanisms of boron carbides were investigated by first-principles calculations, based on the density functional theory. The B12–CBC (13.33 at % C) and B10 C 2 P –CC (28.75 at % C) were studied and then compared with the deformation of regular B11CP–CBC (20.0 at % C). The results show the B10 C 2 P –CC, which has the lowest carbon content, has the highest strength and hardness as well as the lowest toughness. With the increase of carbon content, the rhombohedral symmetry will be broken and the three-atoms chains will be replaced by diatomic carbon chains. These changes may have an influence on their anisotropic deformation mechanisms. For the B12–CBC, the destruction of icosahedra without bending three-atom chains causes structural failure for compression along the c axis; while for compression along the a axis, new B–B bonds are formed, causing an unrecoverable deformation; then it is gradually destroyed until full destruction. For the B10 C 2 P –CC, the anisotropic deformation mechanism is not obvious. For both loading directions, the breakage of B–CP bonds causes the stress to drop, suggesting that the structure is beginning to be destroyed. Finally, the icosahedra are fully destroyed, resulting in structural failure.