Mohammad Farooq Wani

Prof. Dr. Mohammad Farooq Wani

orcid

Research Focus & Metrics

Academic Career Length

28Years (1999-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 1999 in Reliability Engineering & System Safety
Verified
Journal Article
Closed access
MWMohammad Farooq Wani
Mohammad Farooq Wani
OGO.P. Gandhi
O.P. Gandhi

25 November 2016 in Lubrication Science
Verified
Journal Article
Closed access
PDF file
MCM. S. Charoo
M. S. Charoo
MWMohammad Farooq Wani
Mohammad Farooq Wani


1 January 2017 in Materials Today: Proceedings
Verified
Journal Article
Closed access
AAAnkush Anand
Ankush Anand
Mir Irfan Ul HaqMir Irfan Ul Haq
Mir Irfan Ul Haq
KVKaran Vohra
Karan Vohra
ARAnkush Raina
Ankush Raina
MWMohammad Farooq Wani
Mohammad Farooq Wani

1 June 2017 in Engineering Science and Technology, an International Journal
Verified
Journal Article
Open access
MHM. Hanief
M. Hanief
MWMohammad Farooq Wani
Mohammad Farooq Wani
MCM.S. Charoo
M.S. Charoo
The life of a cutting tool is greatly influenced by the forces acting on it during a cutting operation. A machining operation is a complex process. It is very difficult to develop a comprehensive model involving all the parameters. The present study aims to develop a model to investigate the effects of cutting parameters (speed, depth of cut and feed rate) on the cutting forces during the turning operation of red brass (C23000) using high speed steel (HSS) tool. The experimental results are based on full factorial design methodology to increase the reliability and confidence limit of the data. Artificial neural network and multiple regression approaches were used to model the cutting forces on the basis of cutting parameters. In order to check the adequacy of the regression model, analysis of variance (ANOVA) was used. It was clear from the ANOVA that the regression model is capable to predict the cutting forces with high accuracy. However, ANN model was found to be more accurate than the regression model

4 March 2021 in Tribology Transactions
Verified
Journal Article
Closed access
RARahul Anand
Rahul Anand
ARAnkush Raina
Ankush Raina
Mir Irfan Ul HaqMir Irfan Ul Haq
Mir Irfan Ul Haq
MMM. J. Mir
M. J. Mir
OGOvais Gulzar
Ovais Gulzar
MWMohammad Farooq Wani
Mohammad Farooq Wani
The present work aims to investigate the synergetic effect of titanium dioxide (TiO2) and graphene (GnP) nanoparticle additives on the rheological and machining characteristics of biodegradable vegetable oil (rice bran). The rice bran oil has been used in turning of M2 steel using a minimum quantity lubrication (MQL) technique. The effects of varying concentrations by weight (0.5 and 1 wt%) of both mono (rice bran oil/TiO2) and hybrid (rice bran oil/TiO2/graphene) nanofluids have been studied. The rheological studies of both mono and hybrid oils revealed an improvement in the viscosity with an increase in nanoparticle concentration. Furthermore, an improvement in viscosity in hybrid fluids at higher temperatures was observed. The experiments revealed that hybrid nanolubricant shows a significant reduction in tool flank wear and surface roughness by 38 and 11%, respectively, compared to TiO2-based lubricant used alone. The tool wear decreased considerably by about 29 and 32% corresponding to 500 and 1,200 rpm, respectively in the case of hybrid fluid (1 wt% TiO2+graphene) in comparison to the base oil, which considerably enhanced the tool life. Scanning electron microscopy analysis was conducted to study the mechanisms of tool wear at flank faces and crater faces. Chip morphological analysis was performed for the acceptable chips by analyzing the color and structure, depicting the amount of heat generation at the tool–workpiece interface. The results establish that synergism of GnP with TiO2 enhances the tribological properties and hence provides a greener and efficient lubrication methodology.